basically he took a stock flexiclick and gave it a brushless motor. and decided not to explain it to people who may not be familiar with this tool brand's systems.
This looks like a detachable battery on an electric drill I'd imagine he modified the car so that throttle is linked to the trigger and the drill is attached to a differential sending power to the back wheels. An electric drill would have more than enough power to be quick but not too fast.
[Bosch Flexi-Click 12v]<Bosch GSR12V-140FCB22 12V Max Flexiclick 5-In-1 Drill/Driver System https://www.amazon.com/dp/B074GYX6XG/ref=cm_sw_r_cp_tai_RygnAbTTF2DKS>may be worth looking at. It's $170, but Amazon has $30 off Bosch power tools of $150 or more.
That project sounds like it would be an interesting & learning one to take on. I have some old battery powered drills that I might try this out on. But as you note the $20 drill is likely the route to go if you're not looking for a project.
This B&D runs $25 on Amazon and has pretty good reviews (likely you can get closer to the $20 for a generic at Harbor or Wal-Mart)
This DeWalt max XR impact driver and drill kit is on sale for $179 https://www.amazon.com/gp/product/B01A08YKV6/ref=ox_sc_act_title_1?tag=slickdeals09-20&ascsubtag=7482d9d67e1811edbd18eef2e093f6790INT&smid=ATVPDKIKX0DER&th=1
Since you said hand tools. Get yourself one of these or similar, possibly with bigger bits. Drill a bunch of small holes to remove material (as close as possible to each other). Then clean it up with the knives you have. https://www.amazon.com/Mr-Drill-0-6-3-0mm-Jewelry-Making/dp/B08BJ9WDMH/ref=sr_1_5?keywords=hand+drill&qid=1667569155&qu=eyJxc2MiOiI2LjIzIiwicXNhIjoiNS42MyIsInFzcCI6IjUuMDQifQ%3D%3D&sr=8-5
I've never found them too small. Stems of the larger plants don't get too large for them, and the roots work right through them. Smaller plants that grow upward, like basil and such, have root masses to counter balance them, so they don't fall over. Things like tomato and pepper need support anyway, more than even a large net cup can give them. Using one size lets me start everything in about 30mm peat pellets, move them into the 2" net cups where I don't have to pack them in with anything and can keep them in them for life.
I also grow a lot outdoors in milder weather, mostly in 44-gallon totes as Kratky systems. I had a problem with rain collecting in the inset tops, running down through the plant openings, and diluting the nutrient. I worked out a cure using 2" PVC pipe risers in grommets to raise the plant positions by an adjustable amount of up to two inches. That only leave what little can fall directly inside the net cups, which isn't much. And staying with 2" net cups minimizes the area rain can fall on. If you're interested, this is the rainproofing plan. More hole drill work. I had to buy an additional 2-7/8" hole saw for the grommets sized for the pipe, and it did require my 1/2" drill.
And on the drill again, I have a firm belief that the best bargain in tools is the best you can afford. So, my main drill is a DeWalt 20-volt 1/2" drill with two rechargeable batteries. It's sufficiently powerful that I can drill 1/2" thick steel (with patience), the keyless chuck works perfectly, the speed control controls sufficiently subtly to have real control (some cheap drills are supposed to be adjustable speed but really are pretty much on or off), and the batteries can be used with other 20V DeWalt tools. It's $100, but I have two and the oldest has seen hard service and is still in good shape.
OP just to clarify when we all say drill, use a tiny hand drill NOT something powered ! Link for example
I did use 2mm bearings. Here are the links on Amazon where I bought both drill and bearings:
I bought two of these drills super cheap around Black Friday one year and they have been troopers ever since. I use one with a drill bit and the other with a screwdriver bit. Batteries last forever and they can take a beating.
BLACK+DECKER 20V MAX* Cordless Drill / Driver, 3/8-Inch (LDX120C) https://www.amazon.com/dp/B005NNF0YU/ref=cm_sw_r_cp_api_i_GAGKF31ZG625AFP7TK9Z
Look up Bosch drills. Plenty of power for household stuff, and much lighter. https://www.amazon.com/Bosch-PS21-2A-2-Speed-Batteries-Charger/dp/B003BEE12U/ref=mp_s_a_1_6?crid=37RHWTG88ZG09&keywords=bosch+drill&qid=1651503295&sprefix=bosch+drill%2Caps%2C127&sr=8-6 Will literally fit in my pocket.
My friend for $8 Amazon will have this to you in a couple of days. Its the one I have
https://www.amazon.com/Mr-Drill-0-6-3-0mm-Jewelry-Making/dp/B08BJ9WDMH
29% OFF
NOW: $139.00
DEWALT DCD771C2 20V Max Lithium-Ion Compact Drill/Driver Kit
https://www.amazon.ca/gp/product/B00ET5VMTU?fbclid=IwAR2-X6nGB2GOx4trPshsyhDw34TE8\_kgxi7OLWQuAt-DS1TJCGqWTICLpK0&th=1&linkCode=sl1&tag=lilymcalli0ba-20&linkId=8d02a1043f8583561efc39cecba264cd&language=en\_CA&ref\_=as\_li\_...
Agreed. You can get a drill for $30, if not less. That's basically the cost of a trailer rental, never mind gas, and paying someone.
I used baler belt from Tractor Supply Company, as the rubber flaps, when I did mine.
https://www.amazon.com/BLACK-DECKER-Corded-5-2-Amp-DR260C/dp/B00T2VJ93C/?th=1
For all of my Admech purposes of magnetizing, I've used this hand drill. It's really easy, as you literally only have to hold your fingertip on the end and turn clockwise.
I've always started with a smaller drill bit to get the hole started, and then switched to the bigger drill bit to put my magnet in. Has worked like a charm, and you have a lot of control. Additionally, it's not straining on your hand or model at all.
Mr. Pen- Hand Drill with 10 Drill Bits (0.6-3.0mm) https://www.amazon.com/dp/B08BJ9WDMH/ref=cm_sw_r_apan_glt_i_SFK1WJGDDMRZP7NX9AQC?_encoding=UTF8&psc=1
Oh, that's not a drill, it's an impact driver. I'm wayy too dumb to begin to communicate the difference, but I know it's not compatible. This is what I have, it's cheap and works. I have a battery one as well, but this one is cheaper and gives reliable power where a battery can vary based on charge strength.
I would look into other drilling options if you can. I use this little hand drill and it works pretty well
Mr. Pen- Hand Drill with 10 Drill Bits (0.6-3.0mm), Jewelry Drill, Resin Drill, Mini Drill, Hand Drill for Jewelry Making, Pin Vise Hand Drill, Hand Drill for Resin, Micro Drill Bit, Mini Drill Set https://www.amazon.com/dp/B08BJ9WDMH/ref=cm_sw_r_cp_api_glt_i_6M13YC7Q94P1A6CNBW2N?_encoding=UTF8&psc=1
I guess you could do a power drill but that might get away from you and is dangerous if you intend to hold the model in your hand while you drill
So I just bought this a few moments ago. Not sure how it converts to your location but Amazon seems to have some good deals popping up:
Limited-time deal: DEWALT 20V Max XR Cordless Drill Combo Kit, Brushless, 2-Tool (DCK283D2) https://www.amazon.com/dp/B01A08YKV6/ref=cm_sw_r_cp_api_glt_i_dl_84ZAQJH9Z86GQ49RXG26
you could use a small hand drill bit to slowly drill into it and pull out, ive done something similar to an elbow that broke once
Recommend looking at the comparison table at the very bottom of the Amazon Canada page here:
DEWALT DCD771C2 20V Max Lithium-Ion Compact Drill/Driver Kit https://www.amazon.ca/dp/B00ET5VMTU/ref=cm_sw_r_apan_glt_i_M354JKERPXWT2WYYJGV0
That might give you an easy way to compare specs. Most people find the 791/796 to be more than adequate for their DIY needs.
The Milwaukee Assembly driver is a well made tool, but its actually a bit awkward and bulky to use for what it does. I have one and like it, but its really not as ergonomic as it could be. For a small electric screwdriver type tool, its actually fairly big and heavy, and the reversing switch is stupid.
I would recommend the Bosch multi head screwdriver.
I acquired an MTE with the metal bearings completely worn and flat. After completely taking it apart (very carefully) I cleaned the insides using compressed air except for the scroll wheel which I cleaned with soapy water and an old toothbrush.
I replaced the bearings using a hand drill (1mm bit), the SIM card removal tool that came with my phone and then I inserted 3 new ZrO2 2mm bearings .
Overall I spent under $50 and now own a fully working smooth rolling MTE.
You're thinking of the 20v Max XR line. There are plenty of brushed 20v tools. For example, the DCD771 is brushed and is essentially a "20v version" of the older 18v DC720.
In the case of the XR brushless, yes, there is certainly a difference. Thats why I qualified that it was only tools that came in the same/very similar models just different mounts, and not all 20v tools.
A Dewalt drill driver is probably one of the must haves and its just marginally more expensive than a similar Ryobi set to start off with. LINK
IMO if you pair it with a couple of Milwaukee Shockwave PH2 bits (1 in 65mm, 1 in 110mm) it will save a lot of elbow grease in assembling furniture. Might need to add other drill bits as needed.
No need to rush to buy the whole store. You can add the rest as you go along.
I have worked in many computer stores and as a field tech, I bought this guy a few years back and its fucking brilliant.
https://www.amazon.com/Bosch-PS21-2A-2-Speed-Batteries-Charger/dp/B003BEE12U/
DCK283D2. Hope this is what you meant. Also copied link to Amazon.
DEWALT 20V MAX XR Cordless Drill Combo Kit, Brushless, 2-Tool (DCK283D2) https://www.amazon.com/dp/B01A08YKV6/ref=cm_sw_r_cp_api_glt_fabc_5522X65Z01XSGEVF11Y3?_encoding=UTF8&psc=1
If you're not doing something like building a deck or finishing a basement, get a small one (yet still pistol shaped) for the convenience. example
I’m referring to the cordless drill/driver combo where you can select drilling or driving. I’m sure they’re not as effective as the solo tools but they seem to work all right