As a temporary solution, go on Amazon and buy anti vibration pads and slip them under the machine's four legs. Also move the machine a feet away from the wall you share if you can. This should help as a temporary solution.
Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_cp_api_i_QaodCbQRN5J3B
Have you tried turning your subwoofer(s) down or off to see if that's the cause? Or putting them on isolating feet?
If the vibrations are from your subs, SVS makes isolating feet or you can use pads like these.
Decouple it from the floor. Absolutely essential for apartments.
I put mine on a box that raises it about a foot off the floor, and the box sits on appliance vibration pads. Haven't had a complaint since, and can actually run the sub a little hotter than before.
Get some anti vibration pucks to put under the feet. They sell overpriced audio ones but you can get generic ones made for washing machines and they also do a pretty good job.
You can also put a set of them under whatever furniture your table is on for extra damping.
make sure your table is level as well because any tilt is going to make skips or jumps a lot worse.
Finally check your tracking force with a kitchen scale and try increasing it to the upper end of the recommendation for your stylus
Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4
If I could ask you one more question, are there any isolation tools you recommend? I live in an old wooden house which transfers footsteps right to my table and the feet that came in my turntable just don't cut it. I can't wall mount anything or get a new table for quite a while and am wondering if those 20 ish dollar type of isolation pads on Amazon ( https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_cp_apan_glt_i_TWK5338ACCKRCCRD5YKB) would solve the problem in the short term.
if you have a fairly quiet room in the house a lot of the high frequency sounds will be blocked out once you have your ears under the water. low frequency sounds will travel through the floor though. might want to grab 12 of these and place them under the board.
https://www.amazon.com/Diversitech-MP4-V-Anti-Vibration-Pack/dp/B00BVEMLR4/ref=sr\_1\_5?keywords=anti+vibration+pads&pd\_rd\_r=14e9997e-da83-4837-853c-ae52cc20460d&pd\_rd\_w=d8jcO&pd\_rd\_wg=EWENr&pf\_rd\_p=4fa0e97a-13a4-491b-a127-...
I feel your pain, there are few things you can do to reduce noise. Tighten the screw in your bed. Put anti vibration pads under the bed legs and behind the head board. E.g (Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_awdo_navT_a_TX6S7E0Z8Q0EDCSEAZEG). Get a heavier door, if you live in west, doors tend to be hollow, heavier material door close out the noise. Get a padestal fan that makes a lot of noise (white noise is great for noise reduction), make sure to cover the bottom of the door with towel or something thick which reduces noise. Hopefully this helps.
If you added an SSD to save all the camera data, it would be quieter, assuming you can get one big enough. You'd have to make them a separate storage pool so the cameras only record to them.
Before you get fancy and spend money, try adding damper feet to the NAS. Much of the sound of electronics is magnified by transmitting vibrations to the hard surface it sits on. Something like these damper feet may solve your problem. These are overkill, but you can cut them and they're already cheap.
I got these Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_cp_api_glt_fabc_7AQESGCS1525DQPGHW8C?_encoding=UTF8&psc=1
I didn’t care what they looked like. I just wanted something between the sub and the wall alcove behind my screen it’s placed on. No clue if it works or not. Goal was to reduce vibrations going directly into the wall.
Nice! I am experimenting with these at the moment, but I am finding that either a paver on top or a layer of soft foam underneath is still something that I will need.
Those pads are too stiff, in a nutshell. They work great, but are lacking in certain frequency ranges still. (They look sick however.)
I bought these anti vibration pads from Amazon. Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_cp_apa_9dFNAbVYKVG1H
I put them under each clever if the base. THEY ARE AMAZING. I can sometimes not even tell it's printing. I often find myself now checking to see if it's still for some reason. Before you could hear the vibrations through the walls in other rooms.
For the $10 they cost I would recommend them to everyone.
Thank you, this was really helpful. I'm kinda leaning towards one NX3000D amp (or two of those amps, if I go with four shakers... Maybe aurasound ast-2b-4?)
I've got rubber feet mounted on top of these so I'm hoping the vibration will be under control.
Put some anti vibration pads under the printer so it doesn’t resonate through the metal enclosure. Amazon Link
I use anti vibration pads I got from amazon. There a lot of different designs but I use these...
Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4 https://www.amazon.com/dp/B00BVEMLR4/
They are designed to be put under a washer/dryer but they seem to work really well.
4" x 4" x 7/8" Anti-Vibration pads, Qty 4 in total
Helping a friend this weekend who has a Synology NAS Rackstation, approx size is 2U high, by 22" x 24"
For now, she will be placing it on top of an old, heavy wooden microwave cart (on the top).
It's a solid wood unit; but I wonder if adding the above 4"x4" anti-vibration pads placed in each corner would help the vibration/noise
She might be doing a small server rack; but that is long time away. /thanks for reading
I used these instead of stone or other heavier material in addition to some closed cell foam. It's a pricey option, but it works great: https://www.amazon.com/gp/product/B00BVEMLR4
Yes I used these instead of tennis balls: Diversitech MP4-E E.V.A.... https://www.amazon.com/dp/B00BVEMLR4?ref=ppx_pop_mob_ap_share
Get Sorbothane pads or feet. That'll decouple much of the vibration from the floor, which may be most of what your hearing.
There are other brands, but Sorbothane is the one I know of.
Diversitech MP4-E E.V.A. Anti-Vibration Pad, 4" x 4" x 7/8" Pack of 4
These may also help a lot
https://www.amazon.com/dp/B00BVEMLR4/ref=cm_sw_r_cp_apa_fabc_ynjbGbS1C8ZY4
These are top notch vibration isolation pads that some SFX owners have tested to work better than most options
https://www.amazon.com/gp/product/B00BVEMLR4/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1
Try putting some anti-vibration pads between the trainer and the floor. See this as an example
I bought some of these off Amazon https://www.amazon.com/gp/product/B00BVEMLR4/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
I cut them into four smaller 2"x2" squares and printed some feet for the bottom of the printer to hold them in place. My printer already sits on a solid 2" thick wood base but this helped cut the noise and noticeable vibrations transmitted through my enclosure.
Any excuse to go to Princess Auto is a good one! I actually ordered these on Amazon for my bed.
Not overly confident because I think it isnt vibration but moreso shock waves through the ground that causes it to shake. But deft worth a try!
I just use these left the existing feet on and threw them right under the existing feet. It's rubber, yoga mat type material, rubber.