OP could be using something like this
Super handy, but only gives you a single plug at the cable "entry point" behind the TV.
What about this one?
Echogear in Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_apan_glt_fabc_EW19RZGG21QG02AMCF93?psc=1
It’s not terrible. But doesn’t the wire hider thing piss you off? It pisses me off! If you’re doing a hovering TV Mount, pay a few dollars for this:
A console for the TV would work better. If you don't like that, at least you could get the cords out of the way, I like this method. It's easy and completely repairable if you have to move.
This is the kit I used. Super simple to use. It even includes the drill bit for the hole.
You can do a raceway with angles but the cleanest look is to go through the wall.
Something like this is good. Please don’t just cut a hole and run the power cables as that would probably not be up to code!
Since I just went through this, you can if they are low voltage. Sonos's cord is not. I did this
the power for the TV is illegal, atleast in the us. you need one of these kits. extension cables are not rated for in wall.
ECHOGEAR in-Wall Cable Concealer Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_apan_i_4BEJ5J0JYKXKWJX68KV4
The safer thing to do is run the cable through an in-wall cable management tube. This way there aren’t any hidden connections to non permanent wires.
ECHOGEAR in-Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_i_CQ689JVHVPPSSJMMTGFV?_encoding=UTF8&psc=1
Weirdly downvoted. They might as well wall mount their monitor and run the cables down.
OP, if you go that route, I strongly recommend a installing 2-gang mixed voltage old work box on the wall behind your monitor as it isn’t code to run regular power cables in the wall.
If you’re averse to electrical work, you could try this:
https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_glt_i_0KHX7WA9MP5CE53XZ2ZQ
Apparently this is up to code (because they use Romex in the wall). The power brick for the monitor is unfortunately bulky so your best bet is to zip tie power cables in a bundle and mount it all to either the monitor arm or the back of your screen.
The cables for your desktop peripherals and things like the PlayStation are tougher, I’d drill a hole in the desk near the wall on the side of your dominant hand and be done with it.
This is a very easy solution that I did myself. All you really need is a screwdriver and drywall saw. So easy.
ECHOGEAR in-Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_glt_i_RJ2GPENVHCNAX5E51HEX
$60 kit from Amazon, boom couldn’t be simpler.. ECHOGEAR in-Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_glt_i_H7CEDHWQFSTH6KC03Q96
ECHOGEAR in-Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_glt_i_M4JJYKSWEKZ03RDTVV9K
Looks good. Now just hang those pictures and if you can afford it down the road trade the tv out for a Samsung frame tv.
And get yourself one of these https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_glt_i_H6WW7SWXH7G3FPZ8M5YJ?_encoding=UTF8&psc=1
Looking good! If you’re ocd about cables (like myself), you could install a kit like this.
You do you man. I'm extremely risk averse about two things in my life, house fires are one of them. Nothing is worth that risk. Running a 120v wire through a wall? Just do it right. You can get a kit like this that is code legal, certified for in wall use and safe. https://www.amazon.com/Echogear-Power-Voltage-Cable-Management/dp/B07H9C1176/
It’s wall mounted and then I have one of these running through the wall.
https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_api_i_0CROFbWYZ59Q4?_encoding=UTF8&psc=1
I tried to measure it as close as possible so the other end isn’t visible unless you look under the desk
Damn, that's one sexy setup 🤤
As for cable management, if you own the place or don't mind putting holes in the wall, you could get something like this: In Wall Cable Management Kit
Yes, perfectly safe. You can use something like this. The outside of the fireplace shouldn't be getting particularly hot, and if it is you have other issues.
Tapcons will work. I would recommend getting ones that are 2.5" long. That should give you plenty of support and enough length to make it through the mounting bracket and the plaster. If you put liquid nails into the hole, you're never getting it out. A better solution is to break a toothpick in half (or some spare thin copper wire_ and shove it into the hole before you screw in the tapcon.
UPS/Battery backups are cheap insurance to prevent early bulb failure in the event you're using the projector and your power goes out. The UPS would then allow you to shut down your projector properly and get the bulb temp down while the power is out.
If you can do an in-wall power kit, that allows you to move the power source elsewhere in a closet or something you can put the UPS there vs trying to figure out how to mount the UPS next to the projector.
you're not supposed to run a regular electric cable though the wall. (drilling 2 holes, and running a regular extension cord through them is very much against code) This is both due to the type of coatings used, and if the conductor inside is solid wire vs stranded.
doing the same with low voltage (like HDMI or audio) is OK.
​
If you look online, they do make some kits with proper wiring, but they might be too big to be hidden behind an Arc. And you typically have a second box lower on the wall, that you still have to run power to. This is an example, the first one I came across, not a recommendation.
​
Your best bet outside of hiring an electrician to add an outlet, is to use wiremold channels that stick to the wall, and can be painted to match, although you'll still have a bump
​
If you can, hard wire one speaker to ethernet, and they will create their own wifi network. It can be any of them in your system, even one of the surrounds. If you've just got the one group of arc+surrounds you're probably ok on your house's wifi. I think only the arc will join your house wifi, and create it's own network that the surrounds will connect to, but I'm not 100% sure on that.
​
In the Arc, there are speakers that aim towards the ceiling. so if you put it too close to the bottom of your TV, or if the front of the arc is too far behind the front of the TV (like if you have a "thick" wall mount on your TV, but mount the arc on the wall) you'll be blocking those speakers. Sonos recommends at least 4 inches between the bottom of your TV and the top of the arc
​
You'll want to true play once you get everything connected, you'll need an apple device to do this, iPhone or iPad, I don't think any of the new iPhone 12 models are supported yet. This is because they test each phone and microphone combination, to see how accurately they hear the sound in the room.
​
in order to have atmos, your TV must support E-ARC, and not just ARC. If your TV is more than 2 years old, it won't have E-ARC
I really like this echogear kit, I’ve used it several times for myself and family.
Echogear in Wall Cable Management Kit - Includes Power & Low Voltage Cable Management - https://www.amazon.com/dp/B07H9C1176/
There’s an easy way to hide those cords. https://www.amazon.com/Echogear-Power-Voltage-Cable-Management/dp/B07H9C1176/ref=sr\_1\_1\_sspa?
This was easy to install and works great for us
Yes, cut the holes, but don't just leave them open.
Fill them with an in-wall kit designed for this application.
If you have a drill you could always order this: https://www.amazon.com/dp/B07H9C1176?psc=1&ref=ppx_yo2_dt_b_product_details
I'm not the handiest person alive, but I just set one of these up in my living room last weekend and it looks perfect
What about something like this? It's basically a fancy collar you put on two holes in your wall to run wires to your TV.
That looks like a sick setup!
Def gotta do something about those wires though! If you can drill into the walls, I recommend something like this:
https://www.amazon.com/gp/product/B07H9C1176/
​
It'll give your TV that "floating" appearance.
Btw, I did something like that with a similar dual fightstick! https://i.imgur.com/tMws3ox.jpg (Rock on!)
Cleanup those wires, yo
https://smile.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_apa_glt_fabc_S0926EBZDAR3HZ3W3WGA
You could try not getting a longer cord and just put a plug behind the TV. IF you don't feel comfortable working on the outlets, they make a kit that is basically a plug-in unit.
https://www.amazon.com/Echogear-Power-Voltage-Cable-Management/dp/B07H9C1176
Yes I did! I got one of these badboys and it worked like a charm.
https://www.amazon.com/gp/product/B07H9C1176/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
​
Good call about the guitar!
you are not allowed to run a TV power cable in the wall, that is not up to code. You sure that was a licensed electrician?
You need to run a power outlet up behind the tv and plug it in it is simple to do. they make some over priced things that are UL rated and in wall rated that have a pre-made outlet and inlet you can then plug into your outlet... but you are better off just dropping some romex down the wall (or if the current outlet is fed from above it's even better, pull it back up to your new box, then run a new romex wire between the new and old).
​
Here's the dumb ones I'm talking about, it has a romex in side the wall. https://www.amazon.com/dp/B07H9C1176/ref=cm_sw_r_cp_apa_i_8-irFbX5MSR79?th=1 you will also always have an eye score and not have a clean look if you don't have anything below the TV.
To clarify it was "Hide the cables behind the drywall" and not actually a mount. They basically did something like the below link. I'll save the $450 and run that myself in an hour. My inside walls are not insulated so it should be really easy.
​
For sure it is a goofy solution, I think I've even seen these sold on amazon
Hey, so there are a few ways you can do that. If you already have a laptop, let's say a MacBook pro, you can use ROON connected to a streamer (such as the node 2i). YOu can then use something like Apple TV to screen share your MBP screen on the TV.
​
Regarding the TV.. I have it the wires running behind the wall using this..
They make kits that let you plug an existing outlet into a wall outlet, and it is then wired to the new outlet behind the TV. It is the easiest solution for your case where you can use the existing wires to pull the new wire into place.
sample on amazon
They make them in the rectangular style too to match the hole you already have in the drywall on the bottom. Here's one
Personally I'd try to run power to the new outlet behind the TV completely inside the walls to avoid having one outlet plugged into the other in such a visible spot - but if you just want it done quick and easy something like what I linked will work.
Fyi man, that’s a pretty major fire hazard if your cables are just loosely running through your walls. They sell special kits that allow this sort of routing though, give them some thought!
Echogear in Wall Power Kit Includes Low Voltage Cable Management - Hide TV Wires When Mounting A TV - Includes Hole Saw Drill Attachment for Easy Install https://www.amazon.ca/dp/B07H9C1176/ref=cm_sw_r_cp_api_i_cJKgDb8YRMS0Y