What is Reddit's opinion of
HUANUO Single Monitor Mount, Articulating Gas Spring Monitor Arm, Adjustable Monitor Stand, Vesa Mount with Clamp and Grommet Base - Fits 13 to 30 Inch LCD Computer Monitors 4.4 to 14.3lbs?
From 3.5 billion Reddit comments
By popularity on Reddit, this product is:
77 reviews of this product found across Reddit:
A monitor mount, similar to this one. I bought a 27" 4k monitor, and despite the fact that it is much bigger than my previous one, I was forced to place it closer to me - the original stand had 3 legs, one of which was going pretty far back, so there physically was no space left.
Now I can place the screen almost flush against the wall, and can also pivot it. Never used pivot for productivity, frankly it looks ridiculous on this big of a screen, but it's a godsend when it comes to accessing ports.
Why wouldn't any 100x100mm VESA mount fit? Most of them are x-shaped and don't exceed the screw holes.
I use two of these and they work fine with my Gigabyte G24F's.
After trying a dual stand, I switched to multi single arms. It lets you position your monitors better.
With the dual, it can be hard to get them angled towards each other, just didn't feel that good.
I'm not even using nice ones, just cheap HUANUO brand.
Don't know how thick the bar is behind the monitor in the picture, but I would think a gas spring arm would be more than sifficient: https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94/ref=mp_s_a_1_1_sspa?crid=133FDDTMHVZZQ&keywords=huanuo+monitor+arm&qid=1669653986&sprefix=huanuo+monitor+arm%2Caps%2C129&sr=8-1-spons&psc=1&s...
I have this one and it's great granted, it's on a desk. Or if you can setup the rig next to a desk/table, you can clamp the arm on that then.
HUANUO Single Monitor Mount,... https://www.amazon.com/dp/B07T3KCQ94?ref=ppx_pop_mob_ap_share
I just got these yesterday...love them...returned a triple mount for the same reason. Didn't even unbox it. Now ro figure out how to stick the monitor edges together...gonna try gaffers or some velcro.
Maybe go for a clamp style, articulating monitor arm?
Clamp it sideways on the rear side of one of the uprights, then it can "Float" over the wheelbase when needed, and easily moved aside when not.
Something like this: EXAMPLE
Limited-time deal: HUANUO Monitor Mount, Height Adjustable Monitor Arm, Single Monitor Stand with Full Motion Swivel, Monitor Desk Mount Supports Max 30 Inch 4.4 to 14.3lbs, VESA Mount Bracket, Gas Spring Monitor Mount https://www.amazon.com/dp/B07T3KCQ94?ref_=cm_sw_r_apin_dp_V751JQ1FJGK8T1GV7X5G
I use this and it rocks
It looks like that's starting to become the usual discounted price for the CRG9 for now. As far as the monitor itself goes, as long you don't have it too far away the FOV is good enough that you'll be able to see corner apexes for basically everything except some hairpins. That said, it may still be worth considering triples and then putting the side monitors on adjustable desk mounts instead. Not as ideal as a fixed mounted setup, but gives you some flexibility as far as space goes and gives you that extra bit of vision as well.
Another thing to consider, if space is a concern, is that monitor is about 1 meter wide. So if you have room for that, you very well may have room for triples on adjustable mounts. May be worth investigating how each setup may work with some cardboard cutouts.
I recently got two of these for my two 27'' monitors and so far am happy with them. I replaced a dual stand that was not a gas spring. These ones can be set up and then monitor placed after with the screws partially set.
If you're referring to monitor arms, I've got two of these, or at least something similar
HUANUO Single Monitor Mount, Articulating Gas Spring Monitor Arm, Adjustable Monitor Stand, Vesa Mount with Clamp and Grommet Base - Fits 13 to 30 Inch LCD Computer Monitors 4.4 to 14.3lbs https://smile.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_api_gl_i_VA7TJBXJ4VKRSKXYAPWW?_encoding=UTF8&psc=1
I have 2 of these for about 2 months now and like them
Lol nah that’s my bad. I didn’t read properly. I decided to get 2 single mounts just so I have more freedom with set up.
I could not find a compatible dual monitor mount after a few tries, so I went with 2x single monitor mounts that fit perfectly.
HUANUO Single Monitor Mount - Articulating Gas Spring Monitor Arm, Adjustable Monitor Stand, Vesa Mount with Clamp and Grommet Base - Fits 13 to 30 Inch LCD Computer Monitors 4.4 to 14.3lbs https://smile.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_apan_glt_i_KC29WKSFE08NNJ9YA00W?_encoding=UTF8&psc=1
Pretty nice articulating arm clamped onto the side of my desk. It makes it adjustable.
HUANUO Single Monitor Mount - Articulating Gas Spring Monitor Arm, Adjustable Monitor Stand, Vesa Mount with Clamp and Grommet Base - Fits 17 to 30 Inch LCD Computer Monitors 4.4 to 14.3lbs https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_apan_glt_i_XKV24TR39ZQ4G9C3E8RA
its a desk mount that I got off of amazon. its just enough to support my old 27" Acer Predator XB271HU vertically. I dont know if this will work for you, but heres the link for you to take a look at
https://www.amazon.com/dp/B07T3KCQ94?psc=1&ref=ppx\_yo2\_dt\_b\_product\_details
Hi man! Glad u liked :)
The vertical one is an LG ultrawide 25" (2560 x 1080) 60hz IPS
The main one a Asus TUF gaming VG328H1B 32" (2560 x 1440) 165hz - VA panel
Also, to keep in that position, I use a set of monitor arms like this: https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94/ref=sr_1_1_sspa?keywords=monitor+arm&qid=1642440141&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUFHREtTVkRPNEE4RzgmZW5jcnlwdGVkSWQ9QTA0Mjg1MTMxN...
Look on amazon most monitor arms have two options for installation clamp, and bolt through. So you'll need to just drill a small hole and then you're done.
HUANUO Single Monitor Mount - Articulating Gas Spring Monitor Arm, Adjustable Monitor Stand, Vesa Mount with Clamp and Grommet Base - Fits 17 to 30 Inch LCD Computer Monitors 4.4 to 14.3lbs https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_api_glt_fabc_6DXF987T0EAZ9ZFTKHTN?_encoding=UTF8&psc=1
From what I gathered on reddit, you do not need an adapter for the VG27AQ1A. I ended up ordering this arm that'll arrive in 24 Hours. will post an update then.
any tips on buying a single monitor arm (desk clamp+vesa mount)? I was just going to buy this one and see how I liked it. I could always return it, but want to buy something sturdy/trustworthy, don't mind paying $50 or so. Being able to hide monitor cables is a must as well.
Get a pc stand and place the tower elsewhere. I remember I had my tower on my desk for the first 6 months after building my PC. Looks amazing but after a while it gets to be an annoying obstacle in your way.
Also peeps have mentioned monitor stands. This is also a bangin idea. Heres the link to the one I use….
Single Monitor Mount - Articulating Gas Spring Monitor Arm, Adjustable Vesa Mount Desk Stand with Clamp and Grommet Base - Fits 17 to 27 Inch LCD Computer Monitors 4.4 to 14.3lbs https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_api_glt_fabc_190D03NCTNR18HQZ13GS?_encoding=UTF8&psc=1
This is the one I went with. What do you think?
Single Monitor Mount - Articulating Gas Spring Monitor Arm, Adjustable Vesa Mount Desk Stand with Clamp and Grommet Base - Fits 17 to 27 Inch LCD Computer Monitors 4.4 to 14.3lbs https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_api_glt_fabc_6MY0JTNXJ234ADZTFP8D
Any monitor arm should work. They are usually based off weight (which they equate to screen size).
I have a 34" ultrawide running on this monitor and it's decent enough. Movements are a little bit clunky but it holds the monitor still, and is sturdy enough.
As rallymax said, Humanscale is really the industry standard. I believe their flagship are ~$150, but you did ask for the "best".
Those four screws on the back should reveal whats called a VESA mount. The mount can be bought off Amazon.
They're fairly universal, bendy, and inexpensive
The weight limit of the desk is 110. The weight of your monitors and the particular mount should be listed.
Personally I'd recommend getting 2 separate articulating mounts. I personally have two of these: https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_apa_glt_fabc_66YWWDRZWAKR1NHJRGEM
No that's just an idea. You certainly must measure your desk dimensions and find the right monitor arm. I searched for "monitor arm" in amazon and I think this may work. It has 2 pivots so more adjustable. You also need to make sure it hold your monitor's weight.
Another think to take note is that the longer you stretch the monitor from the clamping point, the easier it is to shake.
If you can afford to, you may wish to get something like a hydraulic monitor mount. (It's about 30 USD) I can't be certain if its the camera angle, but it might help with neck strain if you are looking down at the monitor.
The C clamp arms that clamp to the desk will hold dual monitors just fine.
In general almost everyone is better off with 2 single arms though. Dual arms are much more restricted in placement than having 2 independent arms.
This type of arm is my favorite (not necessarily this specific arm, just picked one for reference). They will give you the best ergonomics. These also come in dual, but again 2 singles will give you much better monitor placement options than a dual.
Yes get a monitor stand, it's a game changer. They're usually around 30 USD if they're dedicated for a single monitor, and can be double or triple if it's a more fancy setup that can be extended and mix-matched later with additional arms and supports. You're not going to see it much, I would worry more about the articulations and features than the look.
I got one of these and it's working perfectly (mine is the dual monitor version).
Only just ordered it the other day. Have to wait for it to be delivered (Friday) and then it will sit in quarantine for a few days so not likely going to have any updates for a week or week and a half. I have this monitor arm mount
Setup:
- Monitor: Dell Ultrasharp U2520DR
- Monitor Arm: Simple one from Amazon
- Webcam: Logitech Brio
- Desk Lamp: Modern desk lamp from Target
- Microphone: Yeti Blackout with a basic microphone arm
- 3 in 1 charger for Airpods, Watch, iPhone
- Magic trackpad and keyboard in space grey
- Desk: Ikea electric sit/stand purchased off Marketplace
- Led strip light mounted under desk
https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_apa_i_sWX.Fb5TNNFNZ
There is also a dual monitor version of this
https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_apa_fabc_UP6bGbP19TZM8?_encoding=UTF8&psc=1
Here ya go man! Best of luck with your adventures!
Your next upgrade should be an articulating arm monitor mount so you can get the screen right up behind the wheel.
If you have space beside your desk, I'd suggest setting up the wheel stand right next to the desk and buying a gas spring monitor stand:
This is the one I have for my 27" monitor and it works really well.
Basically, you want to mount the arm to the side of your desk (the side that you set up your wheelstand) and then extend it over to the wheel stand when you want to race. Works really well for me.
>Is the Cooler you recommended as good as the Noctua NH-D15 cooler?
Yup. https://www.youtube.com/watch?v=ASeu5BjaVJo
>What Water Cooling Options would you recommend?
Not with this case since it's designed for air cooling, but def some others like the Corsair 4000D/5000D Airflow or the Lian Li O11 Air Mini, for example.
I might look for a 360mm AIO like the EK AIO or the Arctic Liquid Freezer II, or a 240mm option like the Arctic Liquid Freezer II or the Deepcool LS520, depending on the case and the leftover budget.
>I got the following Compatibility warning:
I talked about it when I mentioned the BIOS flash button. Tutorial vid here.
>In gaming regards, do you think a 3080 with the previous configuration will be able to run Cyberpunk 2077 2k at a 60+ frame rate?
Fair enough. Yeah, the 3080 would still be great for both gaming and DL.
>For the PSU, if I opted to go below a 3090, do you think 850W should be enough?
Depends on the rest of the system, maybe yes, maybe no. Likely, just stick to 1000W.
>Do you think 100 bucks for a Dual-Monitor Arm Stand is too much?
That's a single arm, isn't it? Here's a single, here's a double.
>I have a new list if you want to take a look at it: https://pcpartpicker.com/list/zCkxC6
My thoughts:
- Extra paste is unnecessary
- Sure you want a white case with the black components? Also the Lancool III is great but honestly kinda much.
- PSU should be changed, either a cheaper (but still high quality) 850W unit or a 1000W unit.
- Do you already own that monitor?
Updated list - https://pcpartpicker.com/list/g2GyRv
Thanks man. Sure NP. HUANUO Monitor Mount, Height... https://www.amazon.com/dp/B07T3KCQ94?ref=ppx_pop_mob_ap_share. It’s awesome because the arm rotates sideways so u can keep the desk closer to a wall.
They go on sale for 22 - 25 dollats occasionally. Heck this isn't the best sale but
https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94
$28 right now.
These are the ones my wife and I picked up!
HUANUO Single Monitor Mount,... https://www.amazon.com/dp/B07T3KCQ94?ref=ppx_pop_mob_ap_share
My monitor dosent have stand compatibility should I get a new monitor if so which 24"/27" would you recommend? And I will purchase this stand
[Here's a reasonably priced alternative](https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1).
[Here's a reasonably priced alternative that will work just as well](https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx\_yo\_dt\_b\_asin\_title\_o02\_s00?ie=UTF8&psc=1)
It's got VESA mounting, thankfully, so you can use a monitor arm like this - https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94/
Or anything else with VESA mounting.
Here are some things you can get to make your setup more cleaner:
Monitor arm: https://www.amazon.com/dp/B07T3KCQ94?ref_=cm_sw_r_cp_ud_dp_PBHCH8FPQZ3BP64J3YJK
Ikea Elloven monitor stand w/ drawer (so if you don't want to use a monitor arm you can store all the stuff under your Macbook inside the stand drawer to clean up desk): https://www.ikea.com/ca/en/p/elloven-monitor-stand-with-drawer-white-50474770/
Monitor lamp (since your desk is small not a lot of room for an actual lamp): https://www.amazon.com/dp/B09NX9TPHP?ref_=cm_sw_r_cp_ud_dp_1CBK3H7BKVKFYF1HTBQF
Moft smart deskmat: https://www.moft.us/products/smart-desk-mat?variant=39546363871319
If you want a mouse Logitech just released their new MX Master 3s: https://www.logitech.com/en-ca/products/mice/mx-master-3s.910-006557.html
If you have room for a lamp this cool desk lamp: https://www.gantri.com/products/10104/aim-table-light-by-smart-design/10104-md-snow
Get this USB-C Dock so you only have to plug in one cable when you want to use your MacBook at your desk instead of having 2 cables plugged in: https://www.amazon.com/dp/B07ZVKTP53?ref_=cm_sw_r_cp_ud_dp_4FDTBBW7KWV4KFV2MZMT
Some fake plants to spruce up your desk: https://www.ikea.com/ca/en/p/fejka-artificial-potted-plant-with-pot-indoor-outdoor-succulent-50519764/
nice. from what i have read people say not to go over 30 inches due to not everyone eye are the same but 32 isn't bad. when i google the max pixels for ur device it says 1080p. i would suggest getting a monitor arm. it allow you to adjust the monitor height and distance to reduce neck and back pain or stress. on top of that it will let u bring it closer or farther away so u can adjust to ur liking and comfort.
mounted on a adjustable monitor arm [Adjustable Monitor Arm]
And connected to the Macbook via a Type C Dongle [UGreen Type C Dongle]
These aren't the exact links to my items, but it's the closest ones I can find for you.
The ultrawide was bought at 2019, and so far has no problems yet.
You need a better mount for your monitor, thing like this https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94/ref=sr_1_2_sspa?crid=2I7KX6JKD8IXY&keywords=monitor+arm&qid=1649000025&sprefix=monitor+ar%2Caps%2C139&sr=8-2-spons&psc=1&smid=AAO6TDKV4R7PK&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExQTZJSDlBSEtWT0NBJmVuY3J5cHRlZElkPUEwMzgxNjQ0NlI0SkZUQUpZOTcmZW5jcnlwdGVkQWRJZD1BMDMzOTIzNzdVTURXUkFEQzZWUiZ3aWRnZXROYW1lPXNwX2F0ZiZhY3Rpb249Y2xpY2tSZWRpcmVjdCZkb05vdExvZ0NsaWNrPXRydWU= or this https://www.amazon.com/EVEO-Dual-Monitor-Mount-econimy/dp/B08FRLJBVV/ref=sr_1_1_sspa?crid=2I7KX6JKD8IXY&keywords=monitor+arm&qid=1649000025&sprefix=monitor+ar%2Caps%2C139&sr=8-1-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExQTZJSDlBSEtWT0NBJmVuY3J5cHRlZElkPUEwMzgxNjQ0NlI0SkZUQUpZOTcmZW5jcnlwdGVkQWRJZD1BMDkzMzM4NTIxRkJBRlhVRU8zRlgmd2lkZ2V0TmFtZT1zcF9hdGYmYWN0aW9uPWNsaWNrUmVkaXJlY3QmZG9Ob3RMb2dDbGljaz10cnVl if you add a second monitor
Hey sry I missed this, the stands are this and this
Very solid monitor mounts, have had 0 issues or complaints. You can latch them onto pretty much anything. Since I'm short on space in this apartment, I ended up moving my desk over beneath the island in my kitchen and mounted the monitors to the island counter above the desk.
Here is the link. It is pretty steady, but does move a tiny bit. Not noticeable when the cars camera is shaking anyways
Something like this?
https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94/
I also have a smaller version from this same brand and these are a solid few inches higher, would have to take measurements to really see for sure. I might also recommend this guy as an alternative, mounts to any vesa arm and let's you move your laptop camera up where it should be.
Get you a single arm monitor mount. They are like $30 on amazon. https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_apa_glt_fabc_C635CHTKK7GYHNXXPZ79
Shod get you as low as you need looks like it will clamp to desk as well.
https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
This is the one I used. Works perfectly. Shop around though because there are a lot of good options. But these are built like tanks for the price.
Computer: MacBook Pro 16" with 32GB of RAM and 512GB SSD
Monitor: Samsung 34-Inch SJ55W, 4k resolution
Mouse: Logitech MX Master 3
Keyboard: Logitech MX Keys
Monitor arm: https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Co-starring:
- 7th gen iPad for Sidecar
- An old 1080p Logitech webcam
- A $30 coffee warmer
- A cheapo USB mic
- A disappointing wireless charger from BJ's
Maybe you can make it work with one of these? https://www.amazon.com/dp/B07T3KCQ94
Try this one for the Acer https://www.amazon.com/Single-Monitor-Mount-Articulating-Adjustable/dp/B07T3KCQ94
I don't know about the second one, this might be your best bet https://www.amazon.co.uk/PUTORSEN%C2%AE-Monitor-Arm-Gas-Assisted-Adjustable/dp/B07QGBYSVN
thank you !
countertop is a the 98 inch Walnut Karlby top from ikea
monitor arm is this generic one from amazon, works great
my macbook stand is this one. its made out of high quality aluminum and matches the silver color of macs perfectly.
Deal link: Amazon
Coupon code: Q7EC9EAK
Category-wise subreddits for Amazon Deals:
Is your reddit feed getting flooded with deals for products you are not interested in? Below are our category-wise subreddits where I crosspost from the main sub.
| Category | Subreddit |
|---|---|
| Electronics | /r/Deals_Electronics |
| Computers and Accessories | /r/Deals_Computers |
| Video Games | /r/Deals_VideoGames |
| Home Improvement | /r/Deals_HomeImprovement |
| Clothing and Accessories | /r/Deals_Apparel |
| Grocery | /r/Deals_Grocery |
Discord Server: Instant deal notifications on our Discord Server!
Amazon Canada Deals: /r/OnlineDealsCanada
Disclaimer: The deal links are affiliated. We may earn a small share on qualifying purchases. It does not affect the deal price in any way.
One is part of the aorus monitor.
It’s a KD25F.
And here’s the other one
Single Monitor Mount -... https://www.amazon.com/dp/B07T3KCQ94?ref=ppx_pop_mob_ap_share
I use three single monitor arms mounted to an adjustable metal sawhorse. It's works quite well.
Deal link: Amazon
NOTE: Are you looking for discounts on a specific product? Search for the product in our official Discord Server! We are gearing up for Black Friday and Cyber Monday! Grab the deals before anyone else! Join our Discord Server to get real-time notifications on all deals. We have category-wise Discord channels. Disclaimer: Some deal links on this sub may be affiliated
Paid $23 for this just now with the included coupon code check box thingy, I'll let you know how good it is!
So the desk is from https://deskits.com/ what's nice is that it has a metal storage bay underneath so some cables are hidden there.
I only have monitor cords and I threaded them inside the casing of the monitor arm. https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Most of my peripherals are wireless, I do have a USB-C dock for my work laptop but I store it behind the printer when I'm not using it.
Gas spring monitor arm and then I vesa mounted a laptop holder
They're actually monitor arms from Amazon:
https://smile.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_cp_apa_i_RRGjFb7N8ZXKY
They're attached to the desktop; the Alex unit sits between them.
Monitor stand on amazon. Super handy! https://www.amazon.com/gp/product/B07T3KCQ94/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1
Just a cheap 30 monitor arm off Amazon lol
https://www.amazon.com/dp/B07T3KCQ94/ref=cm_sw_r_fm_apa_i_eZtMEbEQ0F8P4
Popular alternatives to HUANUO Single Monitor Mount...
VIVO Dual Monitor Desk Mount, Heavy Duty Fully Adjustable Stand, Fits 2 LCD LED Screens up to 30 inches, Black, STAND-V002
Amazon Basics Single Monitor Stand, Lift Engine Arm Mount, Black
