the monitor itself sucked for mounting cause it did not accommodate for any type of mounting brackets so i had to make my own attachment but most of it is this mounting arm. pretty much made the entire top mount from this mounting system.
I'm looking to replace an 8 year old Insignia 50" TV, that had an unfortunate demise today.
I've been very happy with the Insignia brnad, but also looking at Hisense and TCL as options. Staying away from onn brand based off of reviews.
Which would be my best best to get? Looking to spend no more than $500 max.
This is the current mount that I have:
VideoSecu ML531BE2 TV Wall Mount kit with Free Magnetic Stud Finder and HDMI Cable for Most 26-55 TV and New LED TV up to 60 inch VESA 400x400 Full Motion with 20 inch Articulating Arm WT8 https://smile.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_apan_glt_i_JYV25TJZD9WS8JHJXWZA
VideoSecu ML531BE2 TV Wall Mount... https://www.amazon.com/dp/B000WYVBR0?ref=ppx_pop_mob_ap_share
Possibly this. It looks a lot like one I bought. I actually bought two because I bought new tv l, couldn’t find the hardware so I could reconfigure it to the new tv, and like you didn’t want to put any more holes in the wall
The wall mount I use for my top monitor is actually a wall mount I got for my TV. Realized I didn’t use my TV much anymore so I decided to put my monitor on it and it fits perfectly. Here’s the Amazon link:
VideoSecu ML531BE2 TV Wall Mount kit with Free Magnetic Stud Finder and HDMI Cable for Most 26-55 TV and New LED TV up to 60 inch VESA 400x400 Full Motion with 20 inch Articulating Arm WP5 https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_api_i_wLQcEb5C8EJ34
There should be 4 small holes on the back in a square shape. Assuming you do have them, this one is pretty good value if you have a stud where you want to put it:
https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apa_i_kvIqFbENKFSKW
More money will get you something more stable and easier to adjust.
Here’s the link to the mount: VideoSecu ML531BE TV Wall Mount for Most 27"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5 https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_api_i_nVGkCbM3FW5FC
The TV is 46" and the mount I got is this one. I guess what I need to know now is whether that IS a stud or not? Does it qualify for mounting? I can put plywood up on two studs but sadly it won't be centered on my wall anymore :(
I have this wall mount which does allow me to angle down. This is the wall mount brought with me from the previous home. Did the one you recommend have anything that this did not?
If I angle it down no issues right?
I have this wall mount which does allow me to angle down. This is the wall mount brought with me from the previous home.
I am using this mount: VideoSecu ML531BE TV Wall Mount https://www.amazon.com/dp/B000WYVBR0?ref=yo_pop_ma_swf since I was very paranoid as well (also had a pillow on my desk for like a week, especially since it is made of glass). It works great, holds a lot of weight and has a good range of motion.
I do not have a second monitor, but if I did I’d probably mount it above if that was possible with a wall mount. I think a desk mount is better for mounting two, unless there’s some way to make a wall mount hold 2. If that wouldn’t work I’d flip it on it’s side next to the ultrawide for reading webpages/text/whatever. I use that at work for software dev and it’s pretty convenient.
I ended up getting the TV! I also have been using this wall mount for a few years now, it'd done well by me. It's also held a '08 50" plasma which was heavy as fuck and didn't have any issues.
It's a really solid set up, I'm super happy so far. https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apa_wZUMAb6KJ6G8J
VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5 https://www.amazon.com/dp/B000WYVBR0?ref=yo_pop_ma_swf
I use VideoSecu mounts exclusively. This VideoSecu ML531BE TV Wall Mount would probably work well for your application. I've been using one for my bedroom TV for 5 years, not a single problem.
I've had 0 issues with this, $25 bucks, amazon best seller.
https://smile.amazon.com/VideoSecu-ML531BE-Monitor-Articulating-Extension/dp/B000WYVBR0/
Don't know why everyone doesn't buy this type exclusively. I've recommended and helped install this to other people as well. It tilts left and right, so you don't even really need to mount it perfect.
Hmm what I can think of is maybe buying 2 of these
VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 in Extension Arm, HDMI Cable & Bubble Level WP5 https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apa_sITJzb0C4XX0Z
And mounting one to the wall to just get distance from the wall, use a peice of plywood or something to be able to connect it to the second one (second one would need to be faced sideways to be able to tilt down)
Idk if that would work at all but only thing I can think of lol
EVGA are generally well regarded for Nvidia. I couldn't tell you about 1440p monitors (I'm a 16:10 man myself) but look for one with VESA mounting, compatible wall mounts are fairly cheap.
I had a similar issue, with a built in that was big enough for a 30" 4:3 TV but wouldn't fit a 40" 16:9 HDTV. I ended up just cutting a custom shelf that bolted into the existing space but hung out of the cabinet just enough to support the stand of the new HDTV. Something light that might work for you and you wouldn't have to deal with a custom mount for each new TV.
Of if there is a solid wood mounting location on either side of that space you could just use one of these.
I have this on a 32" TV, and it looks like if you got a bigger version mounted it out from the wall (like on a 2x4 that is tied to the wall,and had it mounted right at the edge of the window, you could swivel it around and out the window.
I have a TV opening just like that in my house. I used an articulating mount to mount my TV, and it's been fine for the 3 years I've had that setup. I mounted the wall mount to a stud on the side wall of the inset area, and it allows my TV to swing out like a door to access any gear and wiring I have behind it.
I used something similar to this: http://www.amazon.com/VideoSecu-ML531BE-Mount-Plasma-Screen/dp/B000WYVBR0/ref=sr_1_2?s=electronics&ie=UTF8&qid=1447762715&sr=1-2&keywords=articulating+wall+mount
I got this mount: http://www.amazon.com/gp/product/B000WYVBR0?psc=1&redirect=true&ref_=oh_aui_search_detailpage for my 55" Vizio and I was able to install it myself despite not at all being a professional at this stuff. It's been solid since last December. Looks like it's just from one seller now, though.
I don't know what your budget is for a receiver but I paid $430 for a Sony STR-DN860 and it has Bluetooth (supposedly enhances sound over bluetooth?)+Chromecast+7.1 speaker+hdcp 2.2
I like it quite a lot so far but I'm definitely not qualified to say whether it's better over some other brand.
I would buy a mount similar to this (http://www.amazon.com/VideoSecu-Articulating-Extension-Post-installation-ML531B/dp/B000WYVBR0/ref=sr_1_2?ie=UTF8&qid=1381798137&sr=8-2&keywords=tv+mount) and mount it on a post.
A Plexiglas enclosure may be a little elaborate and cost upwards of $100 in parts alone. I would just make a cover for the TV with a good quality tarp and put it over the TV when not in use.
Ha, so I got this mount: https://www.amazon.com/gp/product/B000WYVBR0/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1
and I absolutely would not recommend it for this monitor. Mostly because the VESA bracket is universal, so it's really big and just happens to have holes for 100x100 (what the monitor is). A 100x100 mount would fit PERFECTLY with it, it would just go into the back of the monitor and you wouldn't have any issues. But since that mount has a "universal" one, it's bigger, so you have to use spacers and get creative with screw lengths yada yada, tbh it was a huge headache and I probably would have used something like this if I had to do it again: https://www.amazon.com/AmazonBasics-Wall-Mount-LCD-Arm/dp/B010QZCT5W
I just didn't like that you could see the mount below the monitor with that one, but you get the point of the 100x100 plate.
I used one of these when I needed a mount that could be wiggled around. Worked fine for a 55".
This is what I'm using. So far it's doing pretty well.
I've purchased this one multiple times-- versatile, affordable, and sturdy:
I went with
VideoSecu ML531BE2 TV Wall Mount... https://www.amazon.com/dp/B000WYVBR0?ref=ppx_pop_mob_ap_share
Got this tv wall mount amz
And got ubolts from lowes. The squared off ones. 2.5 inch's.
Then I had to drill 2 holes in the mount for the ubolts to fully go through. I used 2 holes that were already there to start then measured the 2.5 inch's.
Then mounted it with the ubolts going under the top gunner wrapping around the main beam the runs the length of the falcon.
Most tvs will have their VESA sizing on the box or in the paperwork, I've even been seeing more and more of them on online specs for tvs. Once you know the VESA sizing from your tv, then you'll know what mount to buy.
Most mounts are somewhat universal, especially the less expensive ones you can get on Amazon now. I have used two of them and have been very pleased, biggest thing is just finding out how much articulation you really want/need. My tv is currently mounted in a corner, so I got this (link) for $25 and it has been holding my 50 inch LG perfectly, plus I have some ability to move it around depending on where I'm watching from.
Next tv is going over a fireplace, so I'll likely get something more like this since I won't be concerned about rotating the tv. It's bigger so the whole room will be able to see if flat against the wall.
Final thing: buy from Amazon on this, I can't understand how a metal bracket could cost upwards of $175.
​
​
Here is the top mount and here is the bottom mount.
Bottom mount is much smaller and easier to setup and works like a charm.
> I'm not sure that I understand correctly. Are you planning on mounting to the BACK of the cabinet,
The cabinet is set in an alcove of the living room with an open back. It's difficult to reach the back wall studs without paying a lot more for a full motion wall mount. This is due to the cabinet being pushed a few inches away from the wall to run cable.
> I'd suggest you reconsider. Even with large washers & good bolts, you're still seriously risking pulling chunks of the MDF off.
That makes two of us who are concerned! Hence, me asking you smart people if I'm doing something dumb.
>Would it be possible for you to mount a board across the back between the two sides? The stress put on the MDF by the cross-piece would be much less than that of mounting to one side.
>
>If you MUST only mount to one side, I'd suggest that you add a large piece of 1/2" ply on both sides, and use large washers also.
I think you're right that adding some plywood to reinforce would surely help. But, if I went to that amount of trouble and extra expense to measure, cut, paint, sand the reinforcement and new framing, I'd rather just do it the right way.
>What mount are you planning on using?
If I go with the MDF sidewall route, I was considering Videosec ML531BE (amazon link). I'd already bought one a couple years back and have been happy thus far. It advertises as having 180 degree swivel, can extend 20" from the mounting surface (the enclosure is 38.5" wide), and is darn cheap. Fakespot says it has a large number of poor quality reviews. But there still seems to be an overwhelming number of legitimate ones.
If I wanted to do it right and mount to the back wall studs, I'm considering the Aeon 40300 (amazon) or similar like the Kanto FMC4 (bestbuy). Unfortunately, I'm dealing with 24" stud spacing which limits options without having to run plywood. Both have 28" arm extension and can be mounted directly to the studs. Both seem like they'd end up being at least 3 times the cost of the Videosec/sidewall option when all is said and done.
I'm not sure I can envision your room layout, so I don't know if this would work; but have you considered mounting a TV to a wall using an extendable swivel mount? That way a tv "over there" can be viewed "over here". Something like this: https://www.amazon.com/dp/B000WYVBR0
Everybody knows how to operate a standard TV, and be familiar with what is on it. Many may not know how to operate tablet units with a limited offering.
This is the one I'm using for my 55" TCL Roku TV. :) It works very well for me.
https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apa_RnzSBbXB6SHCH
I just went through this with mounting my c8 to an articulating arm on a motorized lift that comes out of our built in cabinets. It was a pain. I had to have a machine shop fabricate some steel plates so I could install the articulating arm mount lower than the actual motorized lift back. It ended up working out beautifully, but a pain to get all the measurements right.
Is your arm the kind with the 400x400 X? If so, can it adjust to the 300x200? or the kind that hooks to two horizontal bars? Why not just move the mount down?
Dunno if this is reputable lol. Just had good amazon reviews. https://www.amazon.com/gp/product/B000WYVBR0/
I never read anything about that - what were people saying?
As long as your mount doesn't wobble, youre fine.
The first wall mount I ordered (because I was just going by weight) was wobbly with this TV so I then ordered this one and it is sturdy as can be.
I was planning on using the 65mm screws that came with the mount.
The studfinder I am using, also in the picture, does have the AC voltage detection. But, like you said, I don't know how accurate this is so I will be sure to very cautious.
As far as the wall material, I'm not sure what it's made of. I'm going to try to find out.
Thank you for your response. Never even considered the material of the sunroom wall.
VideoSecu ML531BE TV Wall Mount for most 22"-55" LED LCD Plasma Flat Screen Monitor up to 88 lb VESA 400x400 with Full Motion Swivel Articulating 20 i https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apap_RpJK64HGnjXmH
Something like this should work https://www.amazon.com/dp/B000WYVBR0/ref=cm_sw_r_cp_apa_iAz6xbJ7XREX8. Just mount it on the side. It might not be perfectly centered over the opening but it will work.
Thanks. Mount below (it is awesome):
This is the mount I got. I'm going to try to mount it either during this week or over the weekend. I'll let you know how it works.
I have my 50" TV mounted to a single stud with two lags. It's an arm mount and the TV is only about 40 pounds though.
OP, why not get a piece of nice plywood to attach to your mount, then use the lags to put into the top of the mount. This is going to be hard to explain, but if you mount the bottom mounting holes to the plywood(use nuts and bolts with the bolt head on the backside flush with the plywood), and the top lags through the plywood and the studs. Then you only make two holes in the wall and the mount is secure. The bottom may try to pull away from the wall when you adjust the TV though.
The bottom has it's force going into the wall and down, while the top has the force going away from the wall and down.
Get a single stud mount. I have had this one for almost two years now. You may need a set of these as well.
I can second the VideoSecu mount, bought a couple of them. Single stud, plenty of reach to pull out and work on cables. Surprisingly beefy for the price.
https://www.amazon.com/gp/product/B000WYVBR0/ref=oh_aui_detailpage_o07_s02?ie=UTF8&psc=1
​
I have the same model TV and this mount worked great for it. Able to pull it out, swivel, tilt, with no problem.