What is Reddit's opinion of
3M Clear Paint Surface Protection Vinyl Film (6 Inch x 60 Inch)?
From 3.5 billion Reddit comments
By popularity on Reddit, this product is:
32 reviews of this product found across Reddit:
I have the 3M Paint Protection Film under them, basically cut to shape maybe a little bigger. Then apply the PPF and sticker goes on top
Also pro tip: I used the leftover PPF on the foot bottoms of the rear doors. I got kids and just by looking at the PPF, it’s definitely protected the car every time the get in and out.
I use little pieces of 3M Scotchgard film to protect my frames from cable rub around the head tube. You can find it in larger or smaller quantities and cut to size. Amazon link: 3M Scotchgard Clear Paint Protection Bulk Film Roll 6-by-60-inches https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_cp_apa_i_h2PSCbCGDJ8DN
I won't say it's never happened, but I worked as a bike mechanic for years and never ran into housing that failed from rubbing on the frame.
I'd get some nail polish that matches the frame fairly well and touch it up. Then put 3M helicopter tape on the area (turn the handlebars back and forth to see all the area the cable hits) and you'll be good. Another good spot to put some tape is on the crankarms where your heel brushes them, and on the top tube if you're going to run a top tube/bento bag.
I’ve used this on my bikes and it applies A LOT easier than a RideWrap. And it’s 1/5 the cost. I don’t cover the whole bike, just the areas where the chain could contact the frame, the back of the seat tube and under the down tube.
3M Clear Paint Surface Protection... https://www.amazon.com/dp/B004VG8DS0?ref=ppx_pop_mob_ap_share
I had a bike rack on the back of my Soul for years. Same concerns as you have, so I put 3M paint protection film on the paint where the rack would contact the car. Worked like a charm. 3M Clear Paint Surface Protection Vinyl Film (6 Inch x 60 Inch) https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_apan_glt_i_TZEYAX166MHTQRGZN449
It's always a good idea to check parts of your bike with the least tire clearance (fork, chainstays, seat tube) for paint wear from all the mud and git you picked up while on your ride. If you have some wear and want to prevent further wear, helicopter tape (like this)
Looks like it was an adventure, ride on!
On my Outrun cabinet the art is VERY close to the edge of the panel. So much so that it's in danger of peeling. My MK Legacy doesn't have that issue but others might. Which leaves me with potentially wearing out the color tape they use instead of t molding.
I may or may not add spacers to elevate my control panel to make it flush. But I probably WILL add some of this...at least to the left side:
https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_cp_awdb_imm_CBS5PRE13287G6DKRP17
Pull control panel. Apply it to inner side first. Then pull it tight over red trim and then down over side art.
The six inch width of the product is almost perfect for the depth of the rail.
Awesome bike! I have it in Grey/Black. Definitely pick up some 3M Clear Paint Protection paint, or something like that, to protect the front break cable from rubbing off paint from the front steering column. I had some paint rubbed off on my 2021 Domane after 4 days, and I wish I had bought and applied it sooner.
Thank you.
The reason I am worried, I do not want it to spread and become an issue that needs extensive autobody work. I live in the rust belt and I didn't notice such minor rust issues on the older car of mine. Now it has paint bubbles in the corners of the doors and such. Even though the car is in great shape (in terms of engine and the way it runs/handles), I will have to dump the car in a couple of primarily due to the rust becoming a safety issue. I do not want that to happen with this one.
What if I fix it the way you suggest and then apply protection film in that area, what are the chances that it will inhibit the rust growth and delay every 2-year proposition to every 4 or 5 years?
I bought sole protectors on Amazon to protect the soles heres the link Check this out at Amazon.com VViViD 3M Scotchgard Clear Paint Protection Vinyl Film (6 Inch x 60 Inch) https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_other_apa_i_YNKVEbJNCR6H6 It was enough to cover 2 pairs of jordans 5s size 10.5
At the time I got my wireless charger, Tesla hadn't released their one yet so my search was limited to third party. I also think at that price, it's probably best to look elsewhere, but I also haven't seen any reviews for the Tesla branded one.
As for the PPF, you can definitely find some on Amazon. Though I've heard some have had problems with being shipped a roll of PPF that was folded. Mine came in perfect condition, was just rolled up. I don't remember exactly which one I got, but I think mine was similar to this. I personally don't know if other local shops carry PPF normally.
Is there a link on where to get the acrylic protector? I don't see any linked in the (now 11 month old) FAQ, nor have I found it on Amazon. I've found 3M tape that I'm considering though, and am open to ideas why it would be a good or bad idea.
I got this and cut it myself: https://www.amazon.com/gp/product/B004VG8DS0/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 It is enough to do 2 full enduro bikes.
Chain stays, down tube, top tube, seat stays, and misc cable rubbing points are where you want em.
I installed by using a warm soap-water mixture. Make sure to cut round edges so that it doesn't catch or peal off. To install, I would first clean the bike, spray the bike with the soap water, then spray the sticky side of the tape with the soap water.
After that I would apply the wet tape to the bike. The wet on wet makes it easy to use an old credit card to squeegee out all the bubbles in the tape.
It has been over a year, and the tape has not discolored, and where I have wrecked, the tape protected the frame, and hasn't torn away anywhere.
Buy some of this and a heat gun and cover up the more vulnerable parts of your frame. Leave the current ones as battle scars to give your bike character.
This is stuff: https://www.amazon.com/gp/product/B004VG8DS0/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
They sell it in smaller sizes for less. Even something half that size would be enough for a dozen bikes.
I used to sell my frames after riding for a couple years. That stuff helped keep the frames looking brand new.
If you're anal enough, you can put the 3M clear bra shit over the top of your tail fairings. A 6x60" roll will only set you back 18$. I find that no matter how protective manufacturers are of the bottom of their luggage, it's never enough.
https://www.amazon.com/Scotchgard-Clear-Paint-Protection-60-inches/dp/B004VG8DS0
You could probably use a clear film that they make for cars like 3M Scotchgard Clear Bra Paint Protection
It is crystal clear so it would show your stickers as they are and also protect them.
This is really common on a lot of bike brands, not just trek, and not just ones with internal routing. Every bike I've ever owned suffered from this growing up. I was smarter with my last bike purchase and bought a couple rolls of 3M Scotchgard Clear Paint Protection Vinyl Film in 6" and 12" sizes and spend a day patiently making templates and cutting the stuff to fit, and wrapped nearly the whole frame/fork. I ride mountain bike trails so I get rock dings in the downtube and rubs on the toptube from my bike rack. I ended up putting 3M Safety-Walk Slip Resistant Tape on the undersides of those tubes for extra protection. All in all it cost less than ridewrap but took some time. If you only wanted to put a couple small pieces around your frame where things rub it would only take a few minutes and cost a couple bucks but it's well worth it, you just have to be patient and use a hairdryer and slightly stretch it when you put it on, and it goes on invisible. Photo: First bike fully wrapped Photo: Starting the second bike.
I’ve been using the 3M stuff (https://www.amazon.com/dp/B004VG8DS0?_encoding=UTF8&psc=1) and cutting it to fit myself on my bikes for years. Works really well and it’s cheap so if you mess up just (carefully) peel it off and cut another one.
I used this: PPF
I also used this on the door sills and the top of the rear bumper. The strip I put on the bumper has already paid for itself a couple times.
I used 3M. You can also precut or have it professionally done. https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_cp_apa_glt_i_8VA8SE0MGFHMP4CFZBPE?_encoding=UTF8&psc=1
I get this stuff and cut out sections for the crotches of the fork and stays, the top of the chain stay, and the bottom bracket area under the chainrings.
Amazon, man.
3M Clear Paint Surface Protection Vinyl Film (6 Inch x 60 Inch) https://www.amazon.com/dp/B004VG8DS0/ref=cm_sw_r_cp_api_glt_fabc_AJTTNRY7GY69QCHBCBV0
There’s different roll widths and sizes.
3M makes clear vinyl, you could put a sheet of it in the area. It's mostly inconspicuous and I assume can hold up to a little gas. https://www.amazon.com/Scotchgard-Clear-Paint-Protection-60-inches/dp/B004VG8DS0
People use it on their hoods for rock chips, etc. I don't see why it wouldn't work.
If you’re not yet going for sidekicks pick up a roll of 3M scratch guard tape for the rails. Pretty easy to cut to size [Helpful Link](www.amazon.com/dp/B004VG8DS0)
These will be super helpful for next time... I cut mine by hand recently.
I used this $20 6" roll of PPF from Amazon that accommodates them nicely: https://www.amazon.com/gp/product/B004VG8DS0/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
That could work but it won't leave you with any room for mistakes. I did have to redo a piece. The cut piece was about 11.5" long and 6" wide which fit the flat section of the sill perfectly. It covers the entire sill from the rubber seal to the black trim.
I bought this: https://www.amazon.com/gp/product/B004VG8DS0/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00657SFPE/ref=ppx_yo_dt_b_asin_image_o07_s00?ie=UTF8&psc=1
This is what i used on my Aspero. Works great. I measured and cut it with my wifes Cricut machine. Amazon
Here's a link to a potential option. 3M scotchguard is what I use. cut it to size and stick it on after making sure the paint is clean. It will come off nicely down the road if you heat it up.
I'm using this stuff and haven't had any issues with it besides it being a pain in the ass to apply.
Popular alternatives to 3M Clear Paint Surface Prot...
Cat Security™ - Catalytic Converter Protection shield, Fits - Toyota Prius 04-09
