What are /r/BossKatana's favorite Products & Services?

From 3.5 billion Reddit comments

Hosa 2 Button latching foot switch:Amazon

​

This^^ is 20 bucks and works good on my 100 Katana head both banks and channels. What you need to make sure you have is a "TRS" CABLE. NOT "TS". It has two rings on the jack instead of one. thats it...have fun!

I really like Katana Librarian:

https://play.google.com/store/apps/details?id=com.appsforamps.katana

Not affiliated in any way, I just really like the app. I'm a Linux user so getting Tone Studio to work on my laptop was a nightmare, now I use Katana Librarian on my tablet exclusively. You'll need an otg adapter to plug it in, but for me it's been totally plug and play. Give the free version a try to make sure you can connect, but the paid version has been the best app I've paid for, maybe ever.

Researching I see that part of the tone is deceptive and comes from the tuning and playing style rather than effects.

"In 1973, Page had been experimenting with an alternative D modal, or DADGAD, tuning often used on stringed instruments in the Middle East, when he hit upon the hypnotic, rising and falling riff."

“Kashmir is built around four mesmerizing riffs, three of which involve the use of open-string unison- and octave-doubled notes, which create a natural chorusing effect and a huge wall of sound."

So apparently a big part of the tone is created by the interplay of sliding unison and doubled notes over the top of open drone notes. I would say that next up might be looking up what a Danelectro tone sounds like since that is what he played. After that dialing in a not-too bright Marshall tone with a fair amount of gain should be all that is left, I can't find mention of any specific effects that he used on Kashmir and with all that drum flanging going on how would you know anyway? :) Maybe some reverb? I be tempted to try just a hint of Slow Gear too for a vintage gear feel.

This should be fine.

https://www.amazon.co.uk/TGI-TGFS2-Latching-Footswitch-Black/dp/B007WSTOCS/ref=sr_1_9?dchild=1&keywords=guitar+amp+footswitch&qid=1621787449&sr=8-9

Keep in mind, you can't connect an expression pedal and a foot switch at the same time.

you can DIY a little single button footswitch that uses a TRS stereo jack and TRS cable.

I used an enclosure like this

https://www.amazon.com/Support-92x38x31mm-Aluminum-Enclosure-Guitar/dp/B015334J9Q

And a single (I believe latching) switch wired to the jack. No LED on mine. Just a switch and a jack but it works and is tiny and cost me maybe $25 for the parts an about 30 minutes trial and error figuring out which wires needed to connect to which pins on the switch and jack.

I just got an M Audio M Gear EX-P from Amazon for about $25 bucks. It came yesterday and definitely does the job an expression pedal should. It’s a plastic housing so if you’re out gigging, it may not last but for $25 it’s pretty good. Here’s the link- M-Audio EX-P Expression Pedal https://www.amazon.com/dp/B000NLRWEI/ref=cm_sw_r_cp_api_i_QCJmDb5SR6SVR

1. There is a dedicated headphone jack. You need a 6.3mm jack though and TRRS headphones (the ones that come with phones) might not work.

2. No. Tone Studio is Windows or Mac only. You should have access to Android apps however in which case Katana Librarian might work for you.

Please keep it in mind that while I do use Katana Librarian on my phone and it works there, I have no idea if it would work on your Chromebook. Consider using the free version to make sure that it works.

Also, please report back with your results. It would be nice to know if Katana Librarian works on Chromebooks or not.

Ah so MKI. You don't need to bother about this variation button. So just don't touch first knob and it will be fine ;). Another tip: if you want to check which sneaky amp is already loaded to your Katana, you can use this android app. The free version is just enough. You will need USB-OTG cable.

https://play.google.com/store/apps/details?id=com.appsforamps.katana&hl=pl&gl=US

They’re okay. They are one of my spare pairs for my bands in ear. The set I like better is surprisingly a pair of Amazon headphones I got. 50MM Drivers Over Ear Headphones MAONO AU-MH601S Studio Stereo Monitor Closed Back Headphones for Music, DJ, Podcast (Silver) https://www.amazon.com/dp/B08CXJDDNB/ref=cm_sw_r_cp_api_glt_fabc_1KJS0WA2WXJXMKKT4XXK?_encoding=UTF8&psc=1

I assume you intend to use the excellent Katana Librarian for Android, in which case you want a USB OTG cable:

https://www.amazon.com/dp/B07L749R9R/ref=cm_sw_r_cp_apa_glt_fabc_Q6ES29APS189J5QMRT31

That's for a newer phone with USB C, if your phone is micro USB you'd need the appropriate but similar cable

Something like this?

This will let you switch between all 4 presets, I use it. You need a stereo cable to switch between all of them.

https://www.amazon.com/dp/B000VXKUL0/ref=cm_sw_r_cp_apa_glt_i_ZMMXQ4VFESMJM9AZXJVX

To make use of a midi switcher you would need to plug your midi switched into your computer, and use FXFloorboard as an intermediate between the midi signals and the katana.

If you have an Android device, I STRONGLY recommend getting the Katana Librarian app.: https://play.google.com/store/apps/details?id=com.appsforamps.katana

It's basically Tone Studio for your pocket (complete with sneaky amps), and Boss should be ashamed they haven't just released their own version yet. Free to try, $9 to buy, and I've never been so glad I spent the $9. You will need an OTG USB cable. I already had one, most people don't, they are <$10.

Oh damn I need one of these!!

EDIT: Found it on amazon, they have a 50w version too. https://www.amazon.com/BOSS-BAC-KTN100-Amplifier-Cover/dp/B07GXWKL9Y/ref=sr_1_4?dchild=1&amp;keywords=boss+katana+100w+cover&amp;qid=1619450463&amp;sr=8-4

I'd recommend the GA-FC with the Boss EV-30 expression pedal. You can plug it directly in to the GA-FC or into the amp. You can use it as a volume pedal and octave pedal or a Wah pedal. Down the road id still want a separate Wah, but to start with id buy a EV-30 cause it gives you more options to play with.

&#x200B;

EV-30

The footswitch is totally optional. If he's just learning (or bedroom player, practicing, etc.) then you might even consider waiting on the footswitch.

If you get one, I would recommend this one which is a great, budget-friendly unit. It requires a special cable like this.

I dont have the footswitch, but have a mkii50w. Just did a bit of research recently. The pedal you have will work, but you need a power supply (presumably for the led lights). I ended up getting this off brand switch, which works like a charm...

https://www.amazon.co.uk/dp/B007WSTOCS/ref=cm_sw_r_cp_apa_fabc_sfwRFb6914QAV

Dude, you're bang on about the fx loop. Very frustrating.

BUT you CAN use a foot switch. Its not the gafc. I bought this one from amazon, and it works like a charm for all 4 channels:

https://www.amazon.co.uk/dp/B007WSTOCS/ref=cm_sw_r_cp_apa_i_c.fOFbKJDE2C4

Or you can get the proper BOSS switch : fs-6 for twice the price....

Do you have an Android phone?

Katana Librarian for Android: https://play.google.com/store/apps/details?id=com.appsforamps.katana&amp;hl=en_US

~~To my understanding, the Android app is created by a 3rd party and is not supported at all by Boss. So it's definitely not an official "app". And might explain why it's so buggy feeling.~~

Nevermind, I was wrong. There IS a 3rd party app for Tone Studio, but never realized boss had an app for the Katana Air.

https://play.google.com/store/apps/details?id=jp.co.roland.boss_katana_air_editor&amp;hl=en_US

You would need one of thesefrom what I understand. A cord directly from your iPhone to amp will not allow you to interface with it because of restrictions on how the iPhone communicates with plugged in external devices

I have the 50MK2 and went with the cheapest two button latching switch I could find on Amazon. Brand name of mine is "Apex" but a quick search isn't bringing any of those brands up.

This one is similar and should work - A friend has this pedal and the 50mk2, he needed to clip the LEDs.

I'm a big supported of the AKG K240's. Great bang for the buck as far as studio monitor headphones are concerned, I've personally used mine for 2-3 years now. Right in your price range.

K240

You can use the speaker from any combo amp. A combo amp is just a head and a speaker in one box.

You can unplug the speaker from the combo and plug it into the head. You have to disconnect the speaker from the combo amp.

The easiest way is just make a cable. This works but you have to disconnect / connect every time you want to switch amps.

You can also build a box using a switched jack that will allow the speaker to receive signal from the combo amp when no cable is plugged in and from the head when a cable is plugged it.

It's just the same type used foe desktop computers are most newer guitar amps.

10' is nice vut 6' is usually enough for home.

Here is one on Amazon US.

It's 10' 14 gauge, 16 gauge (lighter) is heavy enough and cheaper.

I’m emailing them if I can use a $8 usb cable. I think I’m going to want the Bluetooth option for $70.

That app has the sneaky amps I cannot wait to try out. It looks like perfect for my iPad. Cannot wait to try it.

You could use a preamp pedal but at that point you may as well use the preamp you already have in the Katana.

If you decide to try a preamp put it after your pedals. Don't boost the signal going in to your pedals. You could try an EQ pedal, at the end of the line, with the Level or Gain turned up.

Most good preamps cost more than your Katana. This one seems like a bargain.

I use a Boss FS-6 to get all 4 channels.

The FS-6 uses a 9V battery for the LED's. You can use an adapter to allow power from a normal 9V pedal power supply.

Try this adapter and this cable.

I'm not sure it would work but it's a cheap experiment.

Replied elsewhere saying this but that's right. In case you're looking for a non-latching footswitch, I use this one and love it: NUX NMP-2 Dual FootSwitch for Keyboard, Modules and Effect pedals https://www.amazon.com/dp/B07KJGS6V6/ref=cm_sw_r_apan_i_TBKD48SFDGR6TED7GRB8?_encoding=UTF8&amp;psc=1

I use the HOSA FSC-385 Footswitch. https://www.amazon.com/dp/B000VXKUL0/ref=cm_sw_r_apan_i_V93QJQ5B0QV982GKA4QE?_encoding=UTF8&amp;psc=1

You'll have to buy the cable separately. https://www.amazon.com/dp/B000068NYH?ref=ppx_pop_mob_ap_share

Basically, Boss didn't make a version of Tone Studio for Android so another developer did. It has a nice UI and adds the Sneaky Amps collection. Since you're new to the Katana, you're going to want to Google "Katana Sneaky Amps". 🙂

https://play.google.com/store/apps/details?id=com.appsforamps.katana

Ah gotcha. I noticed it's listed on amazon in the US and there are a ton of reviews. Might get a better sense of what it's like from those.

https://www.amazon.com/Standback-Stand-Light-Compact-Adjustable/dp/B000HHUHBI/ref=sr_1_2?crid=2VFQKIF4SFK0M&amp;keywords=standback&amp;qid=1644726909&amp;sprefix=standback%2Caps%2C72&amp;sr=8-2

I use this stand during practice for my 1x12 100w MkII

On-Stage RS6000 Foldable Tiltback Guitar Amp Stand https://www.amazon.com/dp/B0075DO5K6/ref=cm_sw_r_apan_glt_i_DFDNVHPYR3K7B9ENN4T2

Its fine. I don't love it and haven't used it live, I wish I was able to adjust the tilt. It was meant to be a placeholder until I built something more permanent (like an isolation wedge) but I never got around to it.

At this point I'm looking to just add an extension cab and modify my Katana to run an extension out and make it more like a mini half stack.

I can’t speak to an expression pedal but I just got this foot switch from Amazon and it works tremendously well to switch between the 4 channel presets.

https://www.amazon.com/Hosa-FSC-385-Footswitch-Guitar-style-Dual-latching/dp/B000VXKUL0/ref=mp_s_a_1_5?crid=29WMNNPX7FF3E&amp;keywords=boss+katana+footswitch&amp;qid=1643392283&amp;sprefix=boss+katana+foot%2Caps%2C61&amp;sr=8-5

Yep, fairly certain all the MK2s have a rec/phones out. You should be just be able to plug straight into there.

I guess the difference between that and a laptop jack is that it's a 1/4" plug instead of a 1/8" plug that you'd find on a laptop but if whatever headphones you own doesn't have a 1/4" adapter you can get one pretty cheap, like this:

https://www.amazon.com/Amazonbasics-Plated-6-35mm-Headphone-Adapter/dp/B087KG4C1H/ref=sr_1_2?crid=2OO0AEOUJFSTP&amp;keywords=headphone+adapter+1%2F4+to+1%2F8&amp;qid=1642822569&amp;sprefix=headphone+adapter+1%2F4+to+1%2F8%2Caps%2C74&amp;sr=8-2

I used to use a little mixer like this one. The amp goes in one channel, the PC audio into a second channel, then you mix them together to listen through the headphones.

Streamer setup typically means you want to broadcast yourself to twitch or youtube, and that's quite some additional stuff on top..

Recording on Android isn't really all that advanced/usual thing to do. https://play.google.com/store/apps/details?id=com.extreamsd.aemobiledemo claims to have a special low-latency driver for usb interfaces, but it looks like the Katana can only be used with 44.1kHz - but at least it works in a quick test I did Works to multitrack-record the DI along with the wet stereo signal. Trial version is limited to 45s recording via the USB driver, but that's enough to test. Paid version is 9€ + 4€ in-app-purchase for the low-latency audio driver. If you only record yourself over a backing track, then the default android USB-audio driver will also work, despite the higher latency.

But recording on a tiny phone is not really comfortable, not sure whether the tab7 is large enough for the UI to be useful.

As to playing over backing tracks: just feed those in via aux-in (to have it output via the speaker) or feed it in via USB (then you'll only be able to hear it using the rec/headphone out)

You cannot directly plug the joyo speaker out into your Katana but you can do the following:

1.Buy this(or similar) or make one if you can solder.

https://www.amazon.com/Fender-2-Inch-Right-Angle-Speaker/dp/B003AYE8FQ

1. Unhook the cables currently connected to the speaker on the katana.

2. Attach the new cable from above to the katana speaker making sure positive and negative are correct. You may need a pliers to crimp the connectors a little.

3. Plug the other end of the cable into the joyo amp's speaker out.

4. Have fun.

So, after reading this: https://www.reddit.com/r/BossKatana/comments/qyyz9s/can_you_cycle_presets_on_the_katana_50_mkii/hlk2t7o/

I ordered the foot switch they recommend. Won't get it until today, so I can't tell you how good it is. Still, a good price. Be sure to order the right cable.

this will work on the 50. button A changes between preset on the channel and button b changes the channel

https://www.amazon.com/gp/product/B000VXKUL0/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&amp;psc=1

it's less expensive than the boss pedal and does the same thing

If you only have a single input/ouput connection, then forget about recording that way.

The biggest problem with using the rec out in this scenario is that using it will mute the speaker, and if you don't have another output on your laptop for a pair of headphones, you won't be able to hear yourself play. And even if you had another set of speakers connected, the drivers for your audio device likely won't be ASIO compatible/will introduce too much latency to use for real-time monitoring. You might have luck and ASIO4all might support your laptop, but still it's not ideal solution (as laptop speakers typically are bad anyway...) http://www.asio4all.org/

(that's probably also why your DAW doesn't offer it as an input source: no proper driver for real-time recording - might also be that you need to set it from duplex mode to stereo-input first or configure your DAW to use another sound subsystem, but still that wouldn't solve the latency issue/the problem of not being able to monitor yourself properly).

So first check whether your laptop allows for direct monitoring of the aux-input via the laptop's speaker. If you cannot get that to work , then you at bare minimum need a y-splitter cable to connect headphones in addition to your laptop to the mini's rec-out so you can hear yourself play without disturbing latency.

This. I take it you're not using ASIO4ALL right now. It will let you choose the katana as the input and any other device (your laptop's sound card) as the output.

ASIO4ALL

I bought a mono to stereo adapter so that I could use both ears that I have

https://www.amazon.com/gp/product/B08376BD4B

Just a heads up for anyone who runs into this. Not sure if they make one for 1/4->1/4

The PA system should have a stage box to plug the cable into, or perhaps just plug it into the mixing console. But yes, just plug a cable into the line out, and the other end into the PA, the same place a microphone is plugged into. The Katana needs a 1/4 inch cable, the other end may need to be XLR. For example: https://www.amazon.com/TISINO-Cable-Quarter-Unbalanced-Interconnect/dp/B083R47RZK/ref=mp_s_a_1_2_sspa?crid=3CX74XWBDI0RD&amp;keywords=1%2F4+cable+to+xlr&amp;qid=1636148591&amp;sprefix=1%2F4+cable+to+%2Caps%2C270&amp;sr=8-2-spons&amp;psc=1&amp;spLa...

You just need a USB Otg adapter for your phone. I use one like this: Limited-time deal: https://www.amazon.com/dp/B07BS8SRWH/ref=cm_sw_r_apan_glt_fabc_dl_Y7NSAN2P52EDEN362MBT?_encoding=UTF8&amp;psc=1 one

1.Buy this(or similar) or make one if you can solder.

https://www.amazon.com/Fender-2-Inch-Right-Angle-Speaker/dp/B003AYE8FQ

1. Unhook the cables currently connected to the speaker on the katana.

2. Attach the new cable from above to the katana speaker making sure positive and negative are correct. You may need a plies to crimp the connectors a little.

3. Plug the other end of the cable into the orange amp speaker out.

4. Have fun.

These may be a couple of dumb questions, but:

• Was the amp new? If so, you likely have a Katana Mk II and will need the corresponding Tone Studio download.
• You have the amp connected to your computer via a USB cable, correct? One like this: https://www.amazon.com/Behringer-Microphone-X1622USB-Magik-Fulfillment/dp/B0179TUCSY? If not, get one. If so, the cable or USB port may be bad.

Damn!

I ordered one of these so we’ll see what it does.

MIDI Cable,USB 2.0 Type B to iOS Cable,OTG Lightning Cable Compatible with iOS 10.32 or Later Devices to MIDI Keyboard,Electronic Music Instrument,Audio Interface,Midi Controller and More-5FT https://www.amazon.com/dp/B0987FLDG3/ref=cm_sw_r_cp_api_glt_fabc_ZGMJ0KXQTP6DJE720N3C

I am not sure what Country you live in, but where I live, ground hum can be attributed to the houses ground. The ground for our house is chained throughout via the breaker box which is grounded to the incoming water main pipe on the outside.

Any break in that "gound" circuit from the box to my particular socket can result in the ground not acting as an actual ground.

I would test the amp at another house. Worst case scenario, I would have an amp technician open the amp and look to see if the mains ground is properly attached to the chassis.

If it dissapears in another home, then I would just buy a ground hum eliminator.

https://www.amazon.com/Ebtech-Hum-Plug-Style-Eliminator-Cleaning/dp/B07W682STV

I use this folding plastic footstool. It's not slanted, but it is very light, folds very compact and gets it up off the floor to tame the bass and make it easy to adjust knobs without bending too far. I also keep cables under it. The black one looks like it was made to be an amp stand when used with a Katana. Fits the 100 perfectly.

https://www.amazon.com/dp/B07YRKDSG4/ref=cm_sw_r_cp_apa_glt_fabc_Z3JBG4FTAK3XRP81ZVQ8?_encoding=UTF8&amp;psc=1.

A lot of people like this one.

I have this single button footswitch, but it only switches between one bank, not all 4.

Is it a regular quarter inch mono Jack?
Here is one of those on Amazon. Switchcraft is the industry standard.
https://www.amazon.com/Switchcraft-11-Female-4-Inch-Washer/dp/B00C5B20QE/ref=sr\_1\_2?crid=2C3I8O8GXT68N&amp;dchild=1&amp;keywords=switchcraft+1%2F4+jack&amp;qid=1621002636&amp;sprefix=Switchcr%2Caps%2C212&amp;sr=8-2

Here's the footswitch.

You'll also need a trs cable like this.

this one does it: https://www.amazon.de/gp/product/B00NH11KIK/ref=ppx_yo_dt_b_asin_title_o08_s02?ie=UTF8&amp;psc=1

https://www.amazon.com/dp/B0781455FV/ref=cm_sw_r_cp_apa_glt_fabc_WKBYFTHTPTJPK5V07H0Z?_encoding=UTF8&amp;psc=1

I got this one on amazon, $10. It will change the tone of your amp a lot. Also tons of options, effects, distortions.

Unfortunately, they do not include the cable. You just need a USB B type to USB A type. https://www.amazon.com/AmazonBasics-USB-Printer-Cable-Male/dp/B00NH13DV2/ref=mp_s_a_1_3?dchild=1&amp;keywords=usb+b&amp;qid=1617886570&amp;sr=8-3

This is the exact one I bought. Works like a charm!

I have artist mk2 but had the same trouble. My problem was the cable. I bought a new one, and it worked fine. Bought this one. Good luck.

https://www.amazon.com/dp/B0781455FV/ref=cm_sw_r_cp_apa_glc_fabc_K4V0VPFGY5H9J6T94RE7?_encoding=UTF8&amp;psc=1

Yes! You only need an adapter from the input of your phone or tablet (type c etc...) to an USB port, like this for example https://www.amazon.com/JSAUX-Adapter-Compatible-MacBook-Samsung/dp/B07BS8SRWH/ref=mp_s_a_1_2?dchild=1&amp;keywords=usb+type+c+to+usb+adapter&amp;qid=1615969940&amp;sprefix=USB+type+c+go+us+&amp;sr=8-2 And the cable that's used in printers, I can't remember the name of it, but it's the one you plug into your computer in the back of the Amp. Hope it helps!

Yep, you have to use the software. It's worth setting up, it makes it super easy to customize and gives you access to effects and settings not available on the physical amp. You just need a simple USB A to B printer cable, I just bought this Amazon Basics one and it works fine.

Fender has a cheap one for $13, but only switches between 2 presets

https://www.amazon.com/Fender-0994049000-1-Button-FootSwitch-099-4049-000/dp/B001L8NGJ2

https://www.amazon.com/dp/B08FFH9KXD/ref=redir_mobile_desktop?_encoding=UTF8&amp;adId=200041821397931&amp;id=7561008422200059&amp;psc=1&amp;qualifier=1613871286&amp;ref_=syn_sd_onsite_mobileweb_19&amp;spPl=1&amp;uh_it=98d758e138beae3b7a58521a45cc0...

The Hosa footswitch totally works. $30 for switch and cable vs $60 for just the Boss pedal. You def want the TRS cable.

https://smile.amazon.com/dp/B000VXKUL0/ref=cm_sw_r_cp_apa_fabc_9V6YB3KVB7G77JB44Z7M?_encoding=UTF8&amp;psc=1

https://smile.amazon.com/dp/B0010CCC80/ref=cm_sw_r_cp_apa_fabc_A4ZKPJNYBKK88CXSH3YK?_encoding=UTF8&amp;psc=1

get a better pair of headphones. i've had a similar problem and unfortunately the solution is better audio devices. i recomend these https://www.amazon.com/Audio-Technica-ATH-M50x-Professional-Monitor-Headphones/dp/B00HVLUR86/ref=asc_df_B00HVLUR86/?tag=hyprod-20&amp;linkCode=df0&amp;hvadid=198057541178&amp;hvpos=&amp;hvnetw=g&amp;hvrand=15882226260845859171&amp;hvpone=&amp;hvptwo=&amp;hvqmt=&amp;hvdev=c&amp;hvdvcmdl=&amp;hvlocint=&amp;hvlocphy=1014462&amp;hvtargid=pla-381707139357&amp;psc=1

For Android there is Katana Librarian: https://play.google.com/store/apps/details?id=com.appsforamps.katana

However it won't work on a Chromebook because Google doesn't support USB for Android apps in Chrome OS.

These work just fine if you want to save some money.

Be Sure to get a cable like this to go with it.

I've used this for about 3 months on my 50MK2 but the battery seems to run out pretty quickly. I've found a much cheaper solution and it runs on 9V DC, check it out if interested:

https://www.amazon.com/NUX-FootSwitch-Keyboard-Modules-Effect/dp/B07KJGS6V6

Just a random one from Amazon in the UK that was recommended in a Facebook group, of all places. https://www.amazon.co.uk/dp/B016KV79X8 is the one, but I’m sure there are others that would work.

Agree about the charging; ideal would be to plug the transmitter into the jack on the headphones and have both charge from one connection. It’s not the end of the world though and I just have a double charger and two cables ready to go.

The low-friction thing is what sold it to me. I have a toddler at home so anything with wires or that makes noise is basically out. These plus my iPad is the perfect practice setup. I’m looking forward to trying it with my HX Stomp and my bass, when I have chance!

I use something. When I jam with a few guys, my amp was on the floor by my feet and it was hard to hear, so I would put it louder and the guys across the room heard me more than I heard me so they kinda work. I started using something like this. https://www.amazon.com/Donner-Adjustable-Portable-Silicone-Electronic/dp/B081PPHB3H/ref=sr_1_4 I had one and just tipped it up a bit towards me.

If you want it pointing at you, there are better alternatives. But if you are playing in a group and want to hear it more than blasting out your band mates? Having it point more to you than away from your ears should help.

I have this and it works GREAT with the Katana 100: https://www.amazon.com/On-Stage-RS7500-Tiltback-Amplifier-Stand/dp/B0035LCFRW

It certainly makes a difference if your amp was otherwise sitting on the floor. You need the amp pointing at your head and the tilt stand accomplishes this.

You need a printer cable to connect to the back of the Katana.

And an OTG cable to connect your phone to the printer cable

You can still use a foot switch with your 50. Just not the gafc. There's a boss fs6 or fs7. But if you want to pay way less for the same functionality, get this....

https://www.amazon.co.uk/dp/B007WSTOCS/ref=cm_sw_r_cp_apa_fabc_zkNWFbFYA4AND

Source: have katana 50, also have above footswitch.

This will work just fine $20 (USD). One button controls A/B one button controls 1/2.

However, you will also have to purchase a TRS cable (I think that's another $20 or so)

Disclaimer: I am not affiliated in any way with the creator of app that I'm linking.

On Android you can use Audio Evolution Mobile.

You will have to disable MIDI support in the settings to make the Katana work and depending on your device, it might not work well at all.

You will also need an OTG adapter and a device that supports USB OTG.

The app that I linked is a free demo which should be enough to see if it works for you.

I don't own an iPad so I can't help you there.

For both the MkI and MkII amps, there is a 3rd party app for Android (https://play.google.com/store/apps/details?id=com.appsforamps.katana) which connects via USB. There is no version for iOS; the Katana is not USB-class-compliant so Apple prevents it from being able to connect.

The Air is a special case because it has Bluetooth.

FYI: If you have an Android phone, there's the Katana Librarian app. https://play.google.com/store/apps/details?id=com.appsforamps.katana&amp;hl=en_US

Just FYI, there's a Katana Librarian for Android: https://play.google.com/store/apps/details?id=com.appsforamps.katana&amp;hl=en_US

No I bought a different one that cost like 20-30 bucks works great. Hosa fsc-385. It works really good. I also have the boss 50

Link for it

https://www.amazon.com/Hosa-FSC-385-Footswitch-Guitar-style-Dual-latching/dp/B000VXKUL0/ref=mp_s_a_1_3?dchild=1&amp;keywords=hosa+fsc-385+footswitch&amp;qid=1601870229&amp;sprefix=hosa+fs&amp;sr=8-3

https://www.amazon.com/dp/B000VXKUL0?ref=ppx_pop_mob_ap_share

This is what I use. I can switch between banks and channels with it

Edit: make sure to get a trs cable, a normal cable won't work to switch banks.

I know for a fact that this Fender 1-button switch will let you switch between two channels. I have it and have used it for that.

https://www.amazon.com/dp/B001L8NGJ2/ref=cm_sw_r_cp_apa_i_pmbvFb77EQYAJ

The GA-FC is great, but if you don't want to spend the money on one, any switch pedal will do.

https://www.amazon.com/Hosa-FSC-385-Footswitch-Guitar-style-Dual-latching/dp/B000VXKUL0/ref=sr_1_2?dchild=1&amp;keywords=katana+footswitch&amp;qid=1598737950&amp;sr=8-2

The above switch also works for the MK 50. However, all it does is switch between banks. Unlike the GAFC, it can't turn off effect pedals within the bank.

Thank you for the detailed response!

You are correct, I have the Katana 100 mkII head. I hope to build a 2 head rack with a built in raspberry pi or linux based SBC. So this would work.

I was just confused on how the communications with the foot controller would work since its basically midi out only.

Based on your post, I would need something like this?

https://www.amazon.ca/Proster-Adapter-Interface-Converter-keyboard/dp/B07H25QTF1

I really do appreciate your response, Ive played guitar my whole life and programmed computers my whole life but for some reason, midi escapes my comprehension lol.

Sorry if this is a dumb question, but you're not on the "Panel" channel, right? When on Panel, the right footswitch button won't do anything.

I got the same pedal and this cable (https://smile.amazon.com/dp/B000068NYH/ref=cm_sw_em_r_mt_dp_f5dmFb1GSDDPF) and there were no tricks to anything. Just plugged it in and it worked perfectly.

https://www.amazon.com/Superlux-HD668B-Dynamic-Semi-Open-Headphones/dp/B003JOETX8

Found this a while back through this YouTube video https://youtu.be/2LpxZNrkK0U

The cord is pretty long and removable. It's cheap and sounds great with my Katana.

Like in the video, I also switched out the earpads which I recommend. The originals aren't the most comfortable and the replacements are like a couple bucks on Amazon, Ebay, our one of the Chinese web shops.

I'd save for the GA-FC, for sure. It is worth it. If you want a cheap volume/expression pedal, though, I can recommend the M-Audio EXP. Works well (but again, depends on your needs -- I only use it to adjust volume on the fly without using my hands, and sometimes to tweak effects. If you use a volume/exp pedal a lot I'd maybe go Boss/Roland, esp if you use volume expression as the M-Audio seems to have a small range of motion between quiet and loud). Link to it on Amazon Canada is here.

If you have access to an Android device, the app I like the best is Katana Librarian: https://play.google.com/store/apps/details?id=com.appsforamps.katana

You also need a usb otg cable: UGREEN Micro USB to USB, Micro USB 2.0 OTG Cable 2 Pack On The Go Adapter Micro USB Male to USB Female for Samsung S7 S6 Edge S4 S3, LG G4, Dji Spark Mavic Remote Controller, Android Tablets (Black) https://www.amazon.com/dp/B00N9S9Z0G/ref=cm_sw_r_cp_apa_i_1IkCCb4CY3Y8K

I can confirm this one works for me. I really like the interface, it has the sneaky amps and a couple of extra effects, including the Tera Echo, which sounds amazing... I never review anything and I had to give it 5 stars. As with anything tech related, your particular configuration might be trouble but I've had great success with that app.

Nope, it doesn't. This (USB A to B) is what you need, as I recall.

I use a cheap Snark Tuner https://www.amazon.com/Snark-SN5X-Guitar-Violin-Current/dp/B01H74YV56/ref=sr_1_4?s=musical-instruments&amp;ie=UTF8&amp;qid=1550018516&amp;sr=1-4&amp;keywords=guitar+tuner

or if I can't find that I use one of the free guitar tuner iPhone apps.

I got it on Amazon. Speaker Grill Cloth Fabric Silver Turquoise Stripe Yard. What I am using for a logo is going to be in transit for a while. Came from half a world away via eBay.

Oh, the chrome ring is adhesive striping from autozone as well.