I use this
Had the same issue. Installed a new purge valve and didn’t work. Took it to a mechanic and they found out it was a damaged vapor canister underneath the vehicle. I bought a new one and installed myself. Check engine light went away and hasn’t returned.
Genuine Ford 9L3Z-9D653-C Vapor Canister https://www.amazon.com/dp/B0031B6RCK/ref=cm_sw_r_cp_api_i_7NWKQPWMHYQ8PTWFVN12?_encoding=UTF8&psc=1
I just finished installing the S2 Sport lights in the rear from SPV but only wired it to the Aux switches so I can't answer the difficulty of wiring to the tail lights but I'm pretty sure that's the easy part. I didn't find it too hard and here is a good resource with some tips that helped me along the way: S2 Pro Installation. I would just go slow, make sure you leave yourself slack to fish the wire loom up to the front, and use a bunch of twist ties to make sure the loom doesn't end up touching the exhaust when you're happy with the final route. Only tools I needed were the T40 (or T50?) bit and impact gun required to bolt up the lights and put on the ground.
It took about 1.5 hours total to get the wire loom where I wanted it but I had already attached connectors to the Aux wires under the hood since I had installed other lights previously. If you haven't, they're located behind the battery and they only have about 4-6" of wire lead so removing the battery makes the job a little easier. You'll need this crimper if you want to use the connectors from SPV for a clean connections or you can use something like a heat shrink butt splice or solder and heat shrink.
I'm probably forgetting something but ask away if you want more information or run into any issues
I mounted mine on the plastic to the passenger side. Driver's side has radar cruise behind it if equipped. Cheap kit from Amazon and it looks great and has held up great too. But yea unblocking the intercooler helps in boost. License Plate Screws Stainless Steel Screws, Black Screw Covers for Fastening License Plates, Frames and Covers(8 Pack) https://www.amazon.com/dp/B08LYV15ZH/ref=cm_sw_r_apan_glt_i_1F7N035HS59MA97PJTH1?_encoding=UTF8&psc=1
This is what you're looking for (I have it for my Gen 1) There are other kits to tap into the mirror power but these include the resistor. The one I linked doesn't list beyond 2019 F-150 so you might need to search for a different pin configuration. https://www.amazon.com/Dongar-Technologies-Adapter-16-pin-Vehicles/dp/B088P4VFQ7?ref_=ast_sto_dp
Something like this is super simple and cheap for a start - it has a solid mode so you can use it as a chase light. I've run this on stage rallies (as Sweep/Recovery) with no issues - it stays in place at speed and rough roads.
I buy this The wand is nice as you can fish in through some frame rails until it clogs.
Just replaced the door speakers with these:
Infinity KAPPA-86CFX 6" x 8" Two-Way Car Audio Multi Element Speaker https://www.amazon.com/dp/B075ZBM8PQ/ref=cm_sw_r_cp_api_glt_fabc_QKYH9P163M2JEYDQCMF8?_encoding=UTF8&psc=1
With these adapters:
Metra 72-5600 Ford Speaker Harness 1998-UP https://www.amazon.com/dp/B001OAB6BW/ref=cm_sw_r_cp_api_glt_fabc_RVT33NSYDNEGQ4EA7MR0?_encoding=UTF8&psc=1
It makes a huge difference in sound. I also replaced the head unit and added a few sundown 10’s. I am pretty pleased with the sound.
Fuse 27 is a pretty common problem on the Raptor. Ford has a TSB for it to relocate it. The fuse controls the fuel pump relay if I remember right. I was just driving down the road when mine gave me problems, although it usually happens during start up.
https://www.amazon.com/Ford-EL3Z-14293-A-Genuine-Kit-Terminal/dp/B01C39T92A
Don't know if i am allowed to post links but this is what I use. It seems a little expensive but I have one for each vehicle and one I use for rentals. I am rough with it and it has yet to break. Any of them.Amazon link
You can get the kit on amazon for like $10 less than Ford, the instructions should be included with the kit... they're written in a way a monkey could figure out FWIW.
Ford EL3Z-14293-A Genuine Kit - Terminal https://www.amazon.com/dp/B01C39T92A/ref=cm_sw_r_cp_apa_i_oSygCb1SD1CNF
Specialty Performance Parts... https://www.amazon.com/dp/B07V7GXSC2?ref=ppx_pop_mob_ap_share
Ordered from amazon so I could finance them interest free with my amazon card but you can buy them direct from Specialty Performance Parts too. Comes with all the mounting hardware, lights, and wire harness. Only thing I still have to do as a protective measure is to put heat shrink around the connections.
Wanted to see if anyone had tried these: