What are
/r/JeepLiberty's
favorite Products & Services?
From 3.5 billion Reddit comments
The most popular Products mentioned in /r/JeepLiberty:
The most popular reviews in /r/JeepLiberty:
I have Coverking neoprene set in black. They fit really well and don't slide at all. The only thing I've seen so far is that they require you to retighten them every so often, which isn't a problem really. Also, I've noticed that they tend to fade in color slightly. My driver seat cover looks a bit faded now compared to the others. Other than they they are great.
Amazon. I think I paid like $30 for both of mine. You’ll need something to leverage them into the slot, but I was able to use a trenching shovel to get mine in in under 5 minutes.
Crown Automotive Bump Stop Suspension, black https://smile.amazon.com/dp/B009XV0C14/
Oh, those are actually the factory fog-lights. I think only the 2005 - 2007 Renegade Liberties had them, but I may be wrong. They look nice but get broken quite easily by rocks thrown up on the highway. Here is an Amazon link for third-party one, pretty much identical to factory https://www.amazon.com/Depo-333-2028N-AQ-Passenger-Replacement-Assembly/dp/B004I12C08/ref=sr_1_1?ie=UTF8&qid=1537371196&sr=8-1&keywords=333-2028N-AQ
If you turn the key from on to start and get no crank at all it could be the actuator pin in the ignition cylinder.
This is what it looks like and you can find YouTube vids on replacing it, very common failure in our jeeps.
https://smile.amazon.com/Dorman-924-704-Ignition-Actuator-Chrysler/dp/B004BYX8W8
If it turns over (cranks) when you turn the key to start then this is not the issue.
Edit: glad it worked out, thanks for the silver!
Do you already have side rails? If you do then all you have to buy is cross rails and then you can attach anything to those. If you have a flat roof with nothing on it you’re going to have to pick a set of side rails because you don’t want your Thule Box sitting directly on your roof. A roof’s sheet metal can only hold so much weight before it caves in. I bought these inexpensive locking cross rails from Amazon for $108 and hold a lot of weight. Although they are not available right now you can still find them for about the same price at Walmart and many other websites. This set was very easy to install and required only the little wrench they give you. https://www.amazon.com/gp/product/B07Y85WKJP/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
I have the "Coverking Neosupreme" on my '06. Both front and rear. They hold up well, you'll just need to get in the habit of retightening them every couple months. Easy to install and they fit perfectly around the seat. They don't slide, they are comfortable. Yeah I'd recommend these.
I also have an 07, and these seat covers were dirty cheap and fit well. No, they're not super high quality, but they cover my seats. I ended up choosing a fun color over these Jeep branded covers. I just got a universal cover for the back seats, but I don't love the specific one I got. I did note that most universal seat covers have the 40/60 backseat split as 60/40, so be wary of that fitment.
I have a 08 KK 4wd, I replaced mine 8 months ago and I used these from amazon, they feel well built, I’ve gone off roading and they’ve never been an issue.
AUTOSAVER88 Complete Struts Compatible with 2002-2012 Jeep Liberty, Shock Absorber Coil Spring Assembly (4 pcs) https://www.amazon.com/dp/B07GTCHHD9/ref=cm_sw_r_cp_api_i_q4d2Eb0VSKRX5
Autozone and O'relley's and the like have scanners you can use for free. Though I found it useful enough to buy my own.
https://www.amazon.com/gp/product/B00UJV3E12/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
That's the one I own. It's $55 right now, maybe because of the black friday BS. Usually $100. I'm throwing a P0507 code right now, which oddly enough means it thinks I'm idling too high. But I think mine idles normally, it stays under 800 RPM at a rest.But anyways, that's a code I know to be researching now because of that scanner. It's gives me the code and a vague description of what the code means. But I'll google it and then find people with symptoms like mine and what they did to fix it. Handy to have. But not necessary, if you don't mind driving to your local parts store to use their tool. But I have had a number of occasions now where I've had to pull this thing out and pull a code on mine and my GF's vehicles, a couple of co-workers this one time, just been handy to have. Just look up any OBDII reader, just know the really extremely dirt cheap ones are shit. First one I ever bought was some $20 thing from Walmart and it wouldn't read any of the vehicles I tried it with.
https://www.amazon.com/Speaker-Harness-Chrysler-Adapter-72-6514/dp/B096P59YQS
I cut and soldered new ends onto mine, but wish I had just done the adapters. Would have been a lot easier/faster.
Hypersonic Universal Car... https://www.amazon.com/dp/B00MB7EXW6?ref=ppx_pop_mob_ap_share I put these on my KK I was lazy installing them so I didn’t aim them as well as I could’ve so they blast a little low on the windshield
Looks like a backup camera, similar to the turn cameras I was looking at for my RV. Various manufacturers make this style 'module', so they could have added a mirror style backup camera like this one.
https://smile.amazon.com/dp/B0811Q28N6?ref\_=cm\_sw\_r\_cp\_ud\_dp\_C234F9RNFVWHM22MMGW4
Powerbuilt 620471 Unijack - 6000 lb. Capacity , Black, 6000lb, Unijack https://www.amazon.com/dp/B00GJJZ5NI/ref=cm_sw_r_apan_i_ZP16M0APBKP811KPF0H8?_encoding=UTF8&psc=1
This one is great! I have 02 sport, no lift and works great with room to spare
Not sure if you mean the support struts are shot but I just replaced mine two weeks ago with these and they're great! Highly recommend if that's what you're having the issue with? If not then sorry, I'm an idiot haha
2 Pack Rear Window Lift Supports Struts Shocks Gas Springs Props for 2002-2007 Jeep Liberty PM2029 4365 https://www.amazon.com/dp/B079K8W1Y6/ref=cm_sw_r_apan_i_VQKZR305EG7R0988ZAEY?_encoding=UTF8&psc=1
I personally would use a preformed gasket like this one.
https://www.amazon.com/Fel-Pro-TCS46000-TC-Gasket-Set/dp/B000C2GGF4
It is not the right one for a 2012! Just an example.
And if you were going to DIY it, definitely watch some videos on how to. I didn't know how involved it was until I watched a couple of videos. Less complicated than I thought, but still tedious.
Fwitw there is a brand on Amazon too called “Auxito” they have some identical ones and from my experience they have the longest lasting/brightest interior leds on amazon
If you’re still on the fence about bulbs, I’ve been running these led bulbs in mine for a couple years now and thru are flawless. No modifications needed and all I did was re-aim them. From what I’ve been told by multiple places(this doesn’t make me an expert by any means) leds should be alright without a projector. The way I was explained is that leds don’t have nearly as much up-down light scatter as hids. Like I said ive had mine for a couple years now and haven’t had any complaints. Also like other people mentioned, high beams are pretty much useless. I noticed that was the issue with the factory halogens too though so I think that’s just a bad design from jeep
This is the bottle jack I keep in my 07 KJ, and the jack stands I have measure about 11.5" at lowest. They fit nicely into the notches cut into the subframe rail. That 6.something number is definitely wrong, I can crawl all of the way under my KJ without lifting it at all. If anything, I often end up putting my jack on blocks to get the vehicle all the way up.
My cross bars are 54 inch across
These are on Black Friday sale for $58.
Universal Roof Rack Cross Bars, JinsanityPerformance Universal 54'' Adjustable Aero Aluminum Roof Rack CrossBars Raised Side Rail Gap Needed, Cargo Carrier Rooftop Luggage CrossBars for Most Vehicles https://smile.amazon.com/dp/B09L17Q6C3/ref=cm_sw_r_cp_api_glt_fabc_HAWB650PWKRF70R80Q5A?_encoding=UTF8&psc=1
Vinyl wrap. All colors and finishes available. Interior and exterior You could do both doors and some dash to blend it in
3M 2080 M21 Matte Silver 5ft x 1ft W/Application Card Vinyl Vehicle Car Wrap Film Sheet Roll
https://www.amazon.com/dp/B078X3VKBK/ref=cm_sw_r_cp_api_glt_fabc_H1V82MP314A22CTGZPAA
It's called a security torx
11 Pack Torx Head Screwdriver Bit Set,DanziX 1/4 inch Hex Shank T6-T40 S2 Steel 3 Inch Long Security Tamper Proof Screwdriver Drill Tool Kit with 1 Manual Handle https://www.amazon.ca/dp/B0852XFG8Q/ref=cm_sw_r_apan_glt_i_AW98Y78YN3ND58FF9RAT?_encoding=UTF8&psc=1
This one in particular, is an asshole. I used a combination, drilled out the core of the rivet first, then lightly used a flathead to get under the rivet head and pop it out. If you have one of these, that helped at times. Been a while but I do remember this one sucks. I didn't do the greatest job getting one put back on after. May need to go back and do it right. Anyways, drill the core first and then that should loosen it up enough to help ya.
I have used these in the past, on my 2000 Olds Intrigue, and can recommend it. That said, I didn't do it with my 2008 KK, because it would have gotten in my wifes way when she came with me. I've gone through several different mounts, and really like having these VanMass ones. The lower supports for the phone are fixed, so your wired headphone plug may get in the way (or blocked). I removed the radio bezel, installed a 12V port in the lower void, zip-tied a 4-Way USB-C plug and ran cables (sized to fit) and an AUX cable to my phone. I also have a second mount for my work/camping phone that I use for Waze/Google Maps with two of the power cables run to that as well. Hope this helps you u/UncleMcTouchyFinger.
I use a Panavise Dash Mount. You have to remove the stereo bezel and unscrew the stereo to install.
I put a ball mount on mine and have different accessories that I can use (Magnetic mount, phone holder, xm radio head) depending on what I need.
I bought Anco brand rear wiper blades and they work just fine for me. https://www.amazon.ca/ANCO-31-31-11-Wiper-Blade/dp/B000CFSJCY/ref=sr_1_20?dchild=1&keywords=rear+wiper+blade&pd_rd_r=d3409d8f-03da-4d91-b56a-298d36f36fa9&pd_rd_w=IHkTz&pd_rd_wg=qtUzi&pf_rd_p=6e7778d8-cf58-4ad8-bbaf-117f2f710d1a...
never had any luck buying them locally though. either i have to go for a bigger size or they dont attach properly
Could try Solution Finish to bring it back to black. https://www.amazon.com/gp/product/B07S986VKJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Not sure what you're looking to mount. I've got a Panavise Dash mount. It fits between the radio and the dash. It's very sturdy.
https://www.amazon.com/Panavise-Dash-Mount-Models-Years/dp/B07HFKC9LM
This is probably what you'll need, but I'm not a mechanic and you should research it to be sure.
That's the AC compressor clutch. You can replace that without taking it to a mechanic.
Important note. I broke off two screws forgetting to use the washers that came with it spacing the clutch from the compressor.
I ordered these from Amazon a year or so ago for my wife's '06 Liberty. They fit perfectly.
> The suspense is squeaky
You sure it's the suspension? When I got my 2005 Liberty a few months ago it has a creaking noise going over bumps. It was the sway bar bushings. Those bushings are rubber and after 15 years they get somewhat dried out. If that's what you have, just get some silicone lubricant in an aerosol spray can for about $4. Spray into those bushings. My jeep is now 100% quiet.
OR you can replace the bushings with new ones for $12. https://www.amazon.com/dp/B00498WK34/
JeCar Gas Tank Door Locking Fuel... https://www.amazon.com/dp/B07V5558JM?ref=ppx_pop_mob_ap_share
its not meant for a libby so i had to make a jig to get it to fit in idk how much i would recommend it without a full assortment of tools
Magnetic mount is the way to go.
I have one of these in each of my vehicles. It works great because my gf and I both have the metal plate in our phone cases so no matter who is driving can stick their phone up on the dash. I even put one up next to my bed so I can put my phone on it when I go to sleep.
https://www.amazon.com/dp/B00I608BJ8/ref=cm_sw_r_cp_apa_fabc_O6-6FbE5DC71K
this is very close to the one i have, same brand. mine is a little more plain though.
FH Group FH-PU103114 High Back... https://www.amazon.com/dp/B01DYW6ADQ?ref=ppx_pop_mob_ap_share
These are the ones i have and they fit very well and have a nice look in my opinion, theyre cheap and covers both the front and back seats
Roof Rack Cargo Basket, Universal... https://www.amazon.com/dp/B07RXW9P1F?ref=ppx_pop_mob_ap_share with HELLA 005750941 500FF Series... https://www.amazon.com/dp/B001TWD5GY?ref=ppx_pop_mob_ap_share mounted on
Thanks! I find a lot of Liberty's look very "Mall Crawler", I tried to make mine more of an off-road XJ.
The light bar mounts are from Amazon for an XJ. The are very sturdy and we'll made, it leaks a little right now but it could be easily properly sealed.
The bumper is from At The Helm fabrication. Excellant bumper, went on easy and the build quality is second to none
The gas milage is tricky. Recently, I swapped in a new steel driveshaft because the aluminum one was rubbing by gas tank skid plate under high flex. That thing tanked my mpg. Before I installed it I was getting 16-17 highway, which wasn't much different than before all the mods. The driveshaft dropped it to 12-13. But no more rub!
It looks like you may need a puller. The shaft has a centering divot on it I think. A 3 jaw might work or you may need something like this guy. https://www.amazon.com/PMD-Products-Automotive-Compressor-Conditioner/dp/B06XT4M8D2/ref=sr_1_6?dchild=1&keywords=ac+clutch+removal+tool&qid=1602460996&sr=8-6
Are there threaded holes in the face of the clutch?
That's it, looks like this guy:
https://www.amazon.com/Chrysler-HOOD-PIVOT-BUSHING-5020057AB/dp/B008Y71KUK
I think I might try prying that out and figuring out how to secure in onto the end of the prop rod. Probably just pops together hence it popping apart in the first place.
The rod looks backwards in your other photo.
Looks to be part of the "grille reinforcement"
Probably only about $100 and change but it's gonna take a minute to strip it down and replace it.
https://www.amazon.com/Crash-Parts-Plus-Reinforcement-2002-2004/dp/B01KIMC4T4
I used "Solution Finish Black Plastic & Vinyl Plastic Trim Restorer - Car and Truck Polish" on Amazon. It doesn't make the trim black but it restored it to the factory color.
I posted a review with pictures of my green 2005 liberty, I'm unable to add an updated image because Amazon won't let me. It's stayed the same color as when I did it a year ago. I highly recommend, I bought the 12oz because it worked and I used it on multiple cars and I still have a ton leftover.
Check this out: DNA MOTORING FL-ZTL-249-CH Roof Mounted Fog Light Assembly (Driver & Passenger Side) + Switch https://www.amazon.com/dp/B072MJCHXZ/ref=cm_sw_r_cp_api_i_9LCMEb38FFQ54 I️ think I️ found them on amazon
I originally wanted the light bar to be mounted into the slot under the plate but actually I bought the wrong kind of light bar so the mounts weren’t on the side so I ended up getting the bracket. Here is the link ! Right off of Amazon Nilight Led Light Bar Mounting... https://www.amazon.com/dp/B073V2NDQY?ref=ppx_pop_mob_ap_share
This is what I got off Amazon. I couldn't find anywhere local that stocked them. Definitely not the best blade, but I don't use it that much. https://www.amazon.com/gp/product/B07K14Y3CJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
I came across these in a thread about replacements once, maybe you could wire 'em in?
No trouble with our '04's back window, aside from the lifters being a bit squishy. I think /u/mrlavalamp2015 is right about the fact that you'll need the dealership to program the fobs. I've purchased fobs from Amazon for like $25 and they work just fine (strike that: $17 for two) - but if memory serves correctly, you need to have a working fob already associated with your vehicle, in order to add another one. That's why you'll need the dealership in your case. (I know that sounds whack, and I'm honestly not positive whether I'm remembering that correctly.)
As for the chip key, I don't think we actually have one for our vehicle, so I don't have any info on that for you.
Premium Seat Bolt Car Mount Vehicle Holder for Samsung Galaxy Tab S2 S3 S4 A E S9 S8 S7 Plus / Apple iPad Mini, Apple iPhone X 8 7 6 Plus / LG G Pad (5-8") Phones or Tablets w/ Vibration-Free Cradle https://www.amazon.com/dp/B008L3JEQY/ref=cm_sw_r_cp_apa_UAxTAbX8Y1ACX
This is the tablet mount i use, it screws into the passenger seat bolt and is very secure. I use it with a nexus 7