What are /r/Robobrew's favorite Products & Services?

From 3.5 billion Reddit comments

I got mine from a plumbing/hardware shop. BSP = British Standard Pipe thread. 1/4 Inch BSP = 13.16 mm or 0.518 inch outside diameter and 19 threads per inch.

You can get them on Amazon https://www.amazon.com/Pack-Blanking-Compressor-Fitting-FT080/dp/B07MCLYMST/ref=sr_1_4?crid=3W83PQAJ04UW&keywords=1%2F4+inch+bsp+plug&qid=1647459980&sprefix=1%2F4+inch+bsp+plug%2Caps%2C252&sr=8-4

<< I used an old extension cord >>

My extension cord was wrapped around a spool, the inner most sections of that cord heated up/melted the insulation. Something about tighter circles causes more resistance thus heat. Also make sure you use the correct gauge wire.

<<boards not getting enough air flow and hence overheating>>

I bought this to keep mine off the ground. I only use 1 section of the shelf unit which places my Robobrew 12" off the ground still allowing me to lift out the grains.

https://www.amazon.com/Shelving-Storage-Adjustable-Shelves-Bathroom/dp/B08SLK7K8T/ref=sr_1_11?keywords=wire+shelf&amp;qid=1640627000&amp;sprefix=wire+sh%2Caps%2C186&amp;sr=8-11

I measured hot tap water with a pitcher initially "calibrated" to quart lines with a one-cup measuring cup.

I fill the robo to 6.25g before dropping in the grains. After I raise the grains, use the pump to recycle wort across the grains for a minute or two. For sparge I use this tea kettle https://www.amazon.com/gp/product/B07X5J7NRM/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&amp;psc=1 with its temp set to 175F; I generally fill 3-4 pitchers to get back to 6.25 to start the boil. The kettle so much easier than my prior methods. Combine this with crushing my own grains to .333 and hit my numbers (if I had grains delivered pre-crushed I never hit my numbers).

I've been using PBW with great success. I'm not sure if it's available in the UK but I'm sure there is an equivalent.

After I have removed the trub and given it a good rinse I add some PBW powder and enough hot water in the kettle to cover the grain basket. I'll throw my hop spider and anything else that needs a good soak. Then I turn on the burner and set the temp 120 or so. After it gets warm I turn on the recirculation pump and let it go for a good 10 mins or so. PBW is very good at removing stuck on debris. When the 10 min soak is done I drain most of the PBW/water but leave enough to give everything a good scrub using the harder green side of a sponge.

Thanks for the input. I did watch that video previously, though his GFCI inline adapter is sold out, and I haven't been able to find a reasonable priced alternative.

Yeah you could do either, only pro I can think of is that I believe 14-50 is a more standard option to find in homes so if you convert the cord you’ll be more likely to be fine if you move.

I also did a bit more searching and found an adapter as well if you don’t want to do any wiring: https://www.amazon.com/Parkworld-886740-14-50P-Handle-Adapter/dp/B07DR5YPPB

Thank you for the link. As I see it I have maybe two good options with that. Use that cord and replace my 14-50 receptacle with something like this https://www.amazon.com/dp/B01N1P9QV8/ref=cm_sw_r_cp_apa_i_NUtdFbKJS0DTX

Or keep my receptacle, chop the end off your extension cord, and replace with something like this?

https://www.amazon.com/dp/B07L3BMKJP/ref=cm_sw_r_cp_apa_i_2WtdFb4RZD6HD

Pros or cons to either option?

Replacing receptacle probably is easier?

Here’s the extension cord I have: https://www.amazon.com/Parkworld-885590-Industrial-3-Prong-Extension/dp/B07CJH8LPN/ref=mp_s_a_1_3?dchild=1&amp;keywords=6-30r+extension+cord&amp;qid=1594702258&amp;sprefix=6-30r+ex&amp;sr=8-3

I just installed a 6-30 receptacle on a new breaker.

Buy some loc-line for the pump.

I like it for mashing then switch back to the silicone for chilling.

&#x200B;

Loc-Line Coolant Hose Circle Flow

&

Loc-Line Coolant Assembly Kit

&#x200B;