What are /r/Voxelab_Proxima's favorite Products & Services?

From 3.5 billion Reddit comments

I briefly looked into the stepper motor mod. I need to inspect my board and make sure I have the same points to connect to. I've got a different mobo than the one shown in the diagram. I'm still learning all this stuff, this is my first 3d printer of any type. Here the link to what I picked up. https://www.amazon.com/gp/product/B07C7FRLNX/ I went with this one because it had the fastest shipping time. They aren't specifically for the Proxima. It's just a generic stepper motor dampener that mounts between the motor and the top plate.

This is the one i was going to buy before i went with the Voxelab. it is cheaper now than it was just the other day and i can get another $34 off on top of that, making this cheaper than the voxelab. and this one has a built-in carbon filter. before i confirm this, is it a good one? i know it is strictly opinion based, but at least it is an educated opinion...
ELEGOO Mars 2 Pro

I use nFEP sheets. They work better than regular fep sheets. Plus they come in pack of 3.

nFEP Sheets

Why you should use nFEP over FEP

I buy the generic FEP sheets. I used this video:

Changing FEP on Voxelab Proxima

Worked flawlessly. I did print a cap/spacer prior to doing it.

Later I was having intermittent pancaking. I followed the same video above and went with 3 in 1 oil. I rarely have a problem now.

3 in 1 Oil

The new FEP will probably work itself but the oil will help too.

I'm using this and prints fine, keep in mind that they haven't screw holes so there's a bit of DIY involved

Something like this should work just fine for replacing your FEB. You'll need a small razor blade to remove some of the excess when you replace it, but there isn't too much.

I got these. I used to have a screen protector, but there aren't many options out there. The one I got was a little foggy, and I attributed it to failed prints, so I took it off. A bit of a gamble, but we'll see how it turns out. Good luck!

Creality 6PCs UV FEP Film Release Films for ELEGOO Mars/Mars 2 PRO/ANYCUBIC Photon/Photon S/CL-60/LD-002R/LD-002H LCD SLA DLP 3D Printer 200 x 140 x 0.15mm(2 Pieces in Each One Package) https://www.amazon.com/dp/B08BF4BQWQ/ref=cm_sw_r_apan_glt_i_8HGCMN091Q9QEV3X2JQF?_encoding=UTF8&psc=1

I use an ultrasonic bath, and a 50W uv lamp in mirror chamber with solar(uv) turntable inside.

CO-Z 2L Ultrasonic Cleaner with... https://www.amazon.com/dp/B075FTFD3R

FUNGDO 405nm UV Light/lamp for... https://www.amazon.com/dp/B085KW8K3F

I roughed up the original FEP sheet quite a bit with my first "learning" prints. I bought some from the Bezos Barn, and they worked out very well. I pierced the holes with a small screwdriver after lining up the two halves of the frame they go into, then trimmed off the excess from the edges. At about US$2 a sheet instead of US$5 a sheet, I think they're a good deal. https://smile.amazon.com/dp/B08T9HJ4QQ

This is what i use 138mm x 85mm

https://www.amazon.co.uk/gp/product/B09JFQ137C/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1