What are
/r/G35's
favorite Products & Services?
From 3.5 billion Reddit comments
The most popular Products mentioned in /r/G35:
The most popular Services mentioned in /r/G35:
The Pirate Bay
Facebook Marketplace
Emojipedia
OfferUp
The most popular reviews in /r/G35:
Couldn't find the Taotronics one but this looks basically identical:
Mine ended up like this after a tree dropped a limb and I needed a windshield replacement...I couldn't find a like oe replacement. I bought 10ft of this seal and test fitted a bit. Its not perfect (its wider than the oem plastic seal), but it does fit and its better than water flooding in or the ugly curled trim. I have yet to install mine because I am waiting on new wiper arms.
XtremeVision Interior LED for Inifiniti G35 Coupe 2003-2006 (12 Pieces) Pure White Interior LED Kit + Installation Tool https://www.amazon.com/dp/B075TXNM1S/ref=cm_sw_r_cp_api_glc_fabc_uRnaGb96M6N90
Theres a version with the trunk light and plate lights too
I have the exact same issues. I purchased a new drivers-side window motor (not the door lock actuator yet) for $32 from Amazon. From the tutorial videos I've watched for replacing it, it should be less than an hour job to DIY. You'll need an auto trim removal kit ($10 or less) and some other basic tools. Best of luck to you!
The ballasts on the G's are notoriously prone to failure. I would start with the HID bulbs but most likely its the ballast. I don't know how many miles you have on the car but if it's higher mileage I would replace the ballast and go from there. https://www.amazon.com/dp/B07B9KDLQK?ref=nb_sb_ss_w_as-reorder-t1_ypp_rep_k1_1_11&amp=&crid=24091QO4N0RMS&amp=&sprefix=hid+ballast
It's expensive but works really well, installs in the trunk and uses your cars satellite input. Had mine for years with absolutely zero issues. Super clean install in the trunk as well. https://www.amazon.com/USA-BT45-NIS-Bluetooth-1999-2014-Infiniti/dp/B01019UEFK
It's usually inside the assembly. However, you could be creative and add your own in-line check valve like this:
https://www.amazon.com/Fuel-Line-Check-Valve-Lines/dp/B000YOVLBO?th=1
If you have a warranty you should probably replace, but this would also work if it's not under warranty.
Have fun bleeding the coolant lmao. Get this if you don’t want to suffer https://www.amazon.com/Thorstone-Radiator-Automotive-Antifreeze-Universal/dp/B097BHJJPS?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&psc=1&smid=AMHYB4QGJB7JJ
You have to modify it by changing the plastic rings on one of them. There’s a forum post about it somewhere
The thermostat is probably closed because there is air in your system. If you've changed it 3 times in 4 months I think it's very likely you may have a leak where combustion gasses from the engine get into the coolant lines, or you just have air in your system. Your best bet would be to get a lisle funnel, jack the front of the car up put the heat on high, and let it idle until it reaches operating temp. When the thermostat opens make sure the coolant in the lisle funnel doesn't run low. When the car is operating temp let rev it at a constant rpm (2-2.5k) until you feel the heat coming out the vents, and the bubbles stop from the funnel. After that turn the car off and leave the funnel connected with coolant while it cools down for maybe 45ish minutes. The reason for this is there could still be a bit of air trapped and these cars are a pain to bleed. My first car was also a G35, loved it but got rid of it because of a partially blown Head gasket. Regret getting rid of it but such is life. Good luck
Most likely the slave cylinder. It’s cheap enough where it doesn’t hurt to swap it out and it’s the same as OEM. Nabtesco Clutch Slave Cylinder https://www.amazon.com/dp/B001T2XX66?ref=ppx_pop_mob_ap_share
Metra 95-7605 Turbo2 Interface System Double DIN for 2005-2006 Infiniti G35 Sedan and 2005-2007 Infiniti G35 Coupe https://www.amazon.com/dp/B001D0IW8I/ref=cm_sw_r_cp_api_i_JADZZSYH5CCS8WSGA7X7 Here’s the g35 double din kit for 05-07 only And for the stereo it’s called “pioneer avh-200ex” I got mine off someone. You can get any other pioneer stereo though.
Honestly with the way the G’s cooling system is set up air in the system is going to happen a lot so my tried and true method of filling coolant straight into the bleeding port slowly with a long thin funnel usually made the whole process a whole lot quicker. You still have to burp the system the normal way with the heat on full blast and the lisle funnel Lisle 24680 Spill-Free Funnel, Standard Adapters https://www.amazon.com/dp/B00A6AS6LY/ref=cm_sw_r_cp_api_glt_i_A0NB1DNX05DYWXJY9BR0 but that did the trick for me every time.
EVIL ENERGY 2.5'' Inlet 4'' Outlet Exhaust Muffler Tip Universal for Car Stainless Steel 18.5'' Length https://www.amazon.com/dp/B092QY7WFC/ref=cm_sw_r_cp_api_glt_i_CMXXEZZV4KR52F2053B8?_encoding=UTF8&psc=1
Full Synth, high mileage(OFC). Its actually better than most oils since it has the SN PLUS rating, where most oils only have normal SN rating(which is still fine). Amazon doesnt make the oil, its actually made by Warren Distribution in Nebraska.
I was sold on the oil because of this video - https://youtu.be/a9DWGtXpYUc
He is a completely independent dude who is retired and just tests consumer products all day. Tons of other great videos on his channel as well
Yeah they are super expensive, that's why I decided to do it again.
https://www.amazon.com/dp/B08745K56G/ref=cm_sw_r_apan_glt_i_MMJ8V06TH6WEJ122QM1D?psc=1
That's the kit I used. I had to use all sanding disks that came with the kit, mine were really bad tho.
I had the exact same problem. I used 3M Plastic Emblem and Trim Adhesive. https://www.amazon.com/dp/B000CCM3J2/ref=cm_sw_r_apan_glt_i_VVV0QD55SBTTYJDCX856. Been fine for over a year now. Just be sure to take your time and not make a mess. I would carefully remove the majority of the fabric and evenly spread the adhesive on the back foam part then put it back where it goes. You don't have to really use all that much glue.
Plenum spacer. I picked up power from 4400rpm to redline when I put my Blox 5/8", not proven power with a dyno sheet and shit like that but I could feel in the seat without a tune that the motor wasn't getting choked up anymore. (big problem with stock de plenums)
Saves you from buying the $750+ proper made plenums but if your not boosting or doing a crazy N/A build you don't need em.
https://www.amazon.com/Blox-Racing-BXIM-40200-Manifold-Infiniti/dp/B007ZDR2G0
I used a wire splice to connect it to one of the headlight wires on the passenger side. That way when my lights are on, it's on.
Yeah you could do the GPS easy it just sits there, you don't have to modify anything. I can get you a discount if you want one. I love having full-time maps.
Nah mines RWD. PM me and I can help you look through electrical diagrams and we can figure yours out. I might buy a G35X soon so it'd be good for me to know how.
This is the taillight tint: VViViD Air-Tint Headlight/Tail... https://www.amazon.com/dp/B07X4JBHMB?ref=ppx_pop_mob_ap_share
It looks so good, I just need to do it one more time. You need to do it inside or the wind will fuck you. Just buy 2-3 of these (you won't get it right the first time) and a cheap heat gun, and a vinyl tool kit (has like 3-4 things to help you apply the tint) and you're set. If you mess up, it peels right off.
No big deal. The correct way to repair would be to buy a 12x1.25 die to clean up the threads. If you don't want to do that, just thread a nut on (being extra careful not to crossthread) and run the nut over it a few times to smooth it out.
I’d agree with cymbal it’s the starter. Mine went out around 130k mi. The click is the gear that pops out to engage the crank. There is an old trick where if you give the starter a few taps to the starter casing with a rubber mallet as someone else starts the car , it will free up the gear in the starter and crank to get you off the side of the road.
They can be a good test and if it works you’ll know to replace it.
I got my replacement from Amazon I got my replacement from Amazon 4 years ago and it’s still going great
Below is the Amazon link
Agreed. These seats are great (4 way power adjustable plus lumbar lever) minus the headrest.
These are comfy. You end up leaning your seat a little further back with them. It remedied the one pain point I had about the seats
Aukee Car Headrest Pillow with Genuine Leather Memory Foam Supplier Black ( Pack of 2 ) https://www.amazon.com/dp/B01LLHVQQC/ref=cm_sw_r_apan_glt_fabc_G0JPG14WBZ9FP1ZNWMBT?_encoding=UTF8&psc=1
That's the camber. I just put new ones on. Easy and cheap fix, but very important for alignment.
No I had to replace the stock headlights due to yellowing/haziness. Link to headlights
This stuff works wonders and is perfect for scratches like the ones that happened to your car. I've been using it for years and as long as the paint isn't all the way to the body (if your fingernail catches, it's too deep) then it will remove the scratch and even polish the location a little.
MagnaFlow 4in x 9in Oval Dual/Dual Performance Muffler Exhaust 11385 - Straight-Through, 2.25in Inlet/Outlet Diameter, 20in Overall Length, Satin Finish - Classic Deep Exhaust Sound https://www.amazon.com/dp/B000XQQ09Q/ref=cm_sw_r_cp_api_glt_fabc_FG5Z6CQNQ3AA051BWH3F
That’s the 1 I got. Any muffler shop should be able to do the install. Essentially they’ll cut the older resonators out and weld the new one in its place. Yes, it will get rid of that noise when the car comes down from higher rpms. If u search my name. I have a few clips of before and after.
Likely all of your suspension stuff is still the originals from the factory(control arms/bushings/shocks/struts).
I used this - https://www.amazon.com/gp/product/B01ELU9MC6/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
BUT definitely get it all checked out first by a mechanic(its a good idea to get a mechanic friend lol)
AKEPO 16W Fiber Optic Lights Star Ceiling Light Kit APP Control for Car & Home,Fibre Optical Cable Strands 150pcs 0.75mm 6.5ft/2m+28key Musical Remote Control https://www.amazon.com/dp/B07PDF8ZP7/ref=cm_sw_r_cp_api_glt_fabc_FNHHHF99F6FF3SW9T2N3
Definitely sand, polish with meguiers plastx and clear and your good! Unless your headlights are cracked inside like mine were (OEM HID) you could get these: AmeriLite for 2003-2007 Infiniti G35 Coupe HID Type Dual Xtreme LED Halos Projector Black Replacement Headlights Pair - Passenger and Driver Side https://www.amazon.com/dp/B08RMTD6L8/ref=cm_sw_r_cp_apa_i_9VNA3XMS3BQMS9CF3PT9?_encoding=UTF8&psc=1
They are great so far! I haven't seen any condensation in the headlights, build quality is great and its a great alternative to spec D's.
Check for a drainage blocks and make sure there’s no water gathering in the foot wells.
It’s probably just age. My G was doing something similar. You can use kitty litter in a sock or silica gel to take the moisture out the air in the car. I have these Zarpax Reusable Auto Dehumidifier for Car, Truck, Van and SUV, 4-Pack, 4 Count https://www.amazon.com/dp/B01N3507KW/ref=cm_sw_r_cp_api_glc_fabc_Ql5-Fb70XA663?psc=1
Originally just for storing my Porsche but they really do work. One on back deck and stuffed in center bottom of windshield works best for me.
I live in MN so moisture in all it’s forms are an issue.
assuming by kit you mean it comes with the adapter that has RCA connectors? If you have an offbrand radio or it doesn't sound right after install you might need the PAC-ROEM NIS2
​
https://www.amazon.com/PAC-ROEM-NIS2-Interface-Integrate-Amplifiers/dp/B000CE9OY2
The name brand Philips D2R are on sale right now for ~$32 on Amazon.
If it's like this one, and I would think they're all the same, it is part of the headlight assembly itself. You access it horizontally, coming in from behind the light. I seem to recall seeing it in the same general location on my '08 when I replaced bulbs. I was thinking of our other cars in which you position your screwdriver vertically (up/down) and it moves the entire assembly. On these, the bulb and socket swivel up/down inside the housing.
Metra 99-7604 Single/Double DIN Installation Kit for 2003-2004 Infiniti G35 https://www.amazon.ca/dp/B000VYK90Q/ref=cm_sw_r_cp_api_fab_I-ICFbCWG335X
I would recommend the JDM one like this though. It is more expensive but I’ve seen one in person and it’s a lot nicer built than the cheaper one.
https://www.nissanraceshop.com/product/jdm-double-din-kit-03-04-g35-silver/
Edit: just noticed yours is 2006 so I really don’t know what’s best for that 🤷🏼♂️
Details:
This is what I bought for $20. https://www.amazon.com/Aukur-Installation-Infiniti-Projector-Wireless/dp/B07P4MC6P8/ref=sr_1_5?dchild=1&keywords=infiniti+door+light&qid=1597072315&sr=8-5
​
It was not plug and play. The 2-wire harness is different than OEM. I had to cut wires and solder them correctly. It was very easy it just required me to remove the door panel and do the wiring. I used some epoxy to make it fit better. I'm please with the results for the price.
Everything will do that, it's FM radio, it's never going to sound better than FM radio.
The best sounding FM modulator is hardwired into the vehicle's antenna, then it doesn't rely on reception. It requires professional installation, though.
https://www.amazon.com/Is32-Universal-Wired-Modulator-Power/dp/B00ATZGV7W
I bought some replacements off of Amazon because I had two of the original ones "bulge". You don't hear that it's typical with Nissan/Infiniti lug nuts but they did use those crappy designs like many other automakers (Ford had a class-action lawsuit over them). Here's the ones I bought. I wanted some name-brand ones like from McGard but they don't offer any for the OEM wheels. Gorilla has some as well.
I think the OEM p/n is 40224-JK00A.
No wonder my recently bought G35 has a different buttons than the stock ones I look up lol. Someone bought it from Amazon, but the buttons are getting mushy...
https://www.amazon.com/Metra-95-7605A-Installation-2005-2007-Infiniti/dp/B005HIG9PU
These mafuckers look pretty swiggy but I prefer the stock 05' tails.
​
If I was gonna do this mod I would prob start with an aftermarket tail, easier to get into.
Solution Finish Black Plastic & Vinyl Plastic Trim Restorer - Car and Truck Polish - 1 oz. https://www.amazon.com/dp/B006NZQ3T8/ref=cm_sw_r_cp_api_hO03Bb43GZ7Y0
This is the one I got and still have 3/4 left after 2 times use. Dont buy the big bottle because you only use it as little as you can. There a lot of youtube video out there. And it safe for paint to so dont have to tape everything.
They are OEM G37S 19” rims. I had the same vibrations with the spacers on with my stock 18” rims as well. No vibrations without spacers w/ the stock 18” wheels. I’m sure I’d have no vibration with the 19” wheels without spacers, but haven’t tried it because the spacers are necessary for fitment.
They’re both 66.1 bore size as well as the spacers. I don’t have pics of the spacers but I’ll add the links. Disclaimer, they are cheap spacers which would very well be my problem, but I’ve heard of vibrations on the forums even with high quality spacers ... due to a deep bore?
Edit: spelling
20pc Silver Chrome Mag Style Lug Nuts - 12x1.25 Thread Size - 1.5" Length - Installs with 21mm or 13/16" Hex Socket - For many 5Lug Nissan & Infiniti Vehicles Cars https://www.amazon.com/dp/B00OJO89WY/ref=cm_sw_r_cp_api_ttNZBbK6Y8Z93
I ended up buying these. Fingers crossed they work
We’re good to go! The rears for me are weird once they get to the hub, they’re weirdly snug, but once torqued down, seem to be alright. Haven’t driven on them yet, awaiting more lug nuts for the fronts. You definitely need mag lug nuts ..
Magnetic Drawing Board, NextX Big Size Magnetic Writing Pad, Christmas Gifts for Girls and Boys https://www.amazon.com/dp/B00280602C?ref=yo_pop_ma_swf
These are the ones I got, I needed open end for the rears because my spacer’s studs were extra long for some reason. Infiniti wanted $11.95 PER LUG NUG.. fuck that lol
I'm not a 100% sure... I bought all the parts and then had a shop install it...
I did purchase this so I was under the assumption that the Bose stuff was still being used: PAC ROEM-NIS2 System Interface Kit to Replace Factory Radio and ... https://www.amazon.com/dp/B000CE9OY2/ref=cm_sw_r_sms_awdb_t1_kewKBbKMG7D5B
The installer said he wasn't needed, but I didn't get it back, so I'm not sure if it was installed or if they just kept it.
I use this. Has a horribly accented voice on startup (I like it, personally. Makes me laugh every time I start my car) but its never given me problems and it fits in the center console, with the added benefit of a USB plugin to charge your phone.
I had an infiniti (not the car brand) cd slot phone mount. I think it worked the best. Kind of got in the way of the AC buttons a little, but it wasn't that big of an issue. I had a vent mount in my truck once, didn't like it blocking my vent at all, so I wouldn't personally recommend those.
Right now I have a suction cup mount at the top left of my windshield. It's never in my way and I can easily see who is calling or fast forward to the next track while never taking my eyes off the road.
Another thing to consider when looking for a mount is there are two types of mounts as far as how they hold your phone, one grabs it from the sides, the other is magnetic. I like the magnetic ones. You put a thin metal sheet between your case and phone, or under your battery cover if your phone will allow it(if you have a battery cover and the back goes back on with the sheet in there). The downside is it interferes with wireless charging, which I don't use anyway.
Edit: looks like infiniti isn't on Amazon or whatever. Here is the exact same thing. WizGear Rectangular Head Universal CD Slot Magnetic Car Mount Holder, for Cell Phones and Mini Tablets with Fast Swift-Snap Technology https://www.amazon.com/dp/B01K52AE4E/ref=cm_sw_r_sms_apa_difrzbSAW8RC5
You have the exact same model I do. I'd recommend this as a good first mod. Makes it sound beefier: https://www.amazon.com/STILLEN-403235-Z-Tube-Without-Intake/dp/B000HL10PQ/ref=sr_1_1?ie=UTF8&qid=1492025835&sr=8-1&keywords=z+tube
Sorry I completely missed this comment man. Here is the link to the one i purchased. Just so you know, its not a direct fit. You actually have to cut the resonators off the replica and weld the xpipe in its place. I remember paying around $80 i think for them to cut the resonators and weld the xpipe. I did think about getting different kind of tips down the like but i'm currently trying to sell the car so all the projects for it are on hold. Sorry for the late response, hope i'm not too late. https://www.amazon.com/gp/product/B000XQJZ34/ref=oh_aui_detailpage_o06_s01?ie=UTF8&psc=1