What are /r/mazda's favorite Products & Services?

From 3.5 billion Reddit comments

The Focus's automated manual transmission has a clutch instead of a torque converter, which is why people call it an automated manual. It's a joint venture with Getrag

https://en.wikipedia.org/wiki/Ford_PowerShift_transmission

http://www.consumerreports.org/cro/magazine-archive/2011/september/cars/small-sedans-hatchbacks/automated-manual-transmissions/index.htm

Lube tech here, I've removed dozens of these without the keys. You'll need either a cheap 12 point socket that you dont care about, or an extractor socket like this(Irwin Tools 53915 Irwin 13/16"- 21mm Bolt Extractor https://www.amazon.com/dp/B0027S98EC/ref=cm_sw_r_cp_apa_i_cenlDbWDJZJG8)

You'd probably need a set since i'm not sure what size would fit, but get either of those and a hammer and pound it over the lug. Then use whatever method of removal(manual or with an impact gun to remove the lug and then pound the old lug and repeat. You will need new lug nuts afterwards.

Your new CX-9 requires a low calcium 5w30 oil.

The CX-9 uses 5w30 instead of 0w20 because that is the viscosity required to properly lubricate the turbocharger.

The tricky part here is the "low calcium" bit. There is a phenomenon known as "surface pre-ignition" that is caused by combustion chamber deposits. More specifically mineral deposits on the exhaust valves of the engine caused by oil additives. Calcium phosphates happen to be a main ingredient in detergent additives in your oil. Mazda engineers have spec'd out a low calcium oil to help prevent this from happening. For anyone who is extra nerdy like me, there is an excellent paper on the subject

TL;DR Read and follow your owners manual

Enjoy your new CX-9!

I replaced the standard door lights with this product off of amazon, very simple installation process that the link gives you.

https://www.amazon.com/DELEIKA-welcome-shadow-Atenza-LOGO-5/dp/B06XQ65M26

It places selected apps from an Apple or Android smartphone on the vehicle's display.

Here's Apple's spiel.

(Edit: But Alas, my Mazda's two years too old).

Spend a few dollars (less than 10) on a Bluetooth ELM327 reader from eBay. If you have an Android phone then all you'll need is to plug it into the port, pair it with your phone and use this app Torque Lite to read the error code yourself.

If the first 2 pics are what came off your car you ordered the wrong bulbs. The second 2 pictures are D2S HID bulbs that probably fit the more expensive model of you car. What you are looking for are Halogen H11 bulbs seen here

Waze was just updated to work with Android Auto and it's been great. Now that I've been using that over Google or my Ford navigation, I can't wait for Android Auto to make its way into the wife's CX-5.

There is the MZD AIO project, but we have the newest Mazda version in the CX-5 that it can't work on.

This survey

>measures customer satisfaction with service at a franchised dealer or independent service facility for maintenance or repair work

So it might not reflect on the actual car itself?

I can see why to a degree. I have to drive 30-40 miles to the nearest accessible dealership that does service and it's usually not worth it to drop off and come back so I'm left waiting for 2-3 hours each time. It once took an entire afternoon to find and fix a creak. Even I wouldn't rate it very high based on that metric.

As for satisfaction with the car itself, consumer reports has a survey that doesn't put mazda near the bottom.

>Model satisfaction is determined by the percentage of owners who responded “definitely yes” to the question of whether they would buy the same vehicle if they had it to do all over again

In this question, I would say 'absolutely yes'.

I bought my 2004 Mazda 3 in early 2010 with a similar question nagging me. "Do i get the hatchback or the sedan". After 4 years and 50k miles, I couldn't be happier with my decision to get the hatchback. It's versatility never ceases to amaze me. I even started taking pictures of just how functional my car is. https://imgur.com/a/CTchD This car has taken myself and 3 friends (and all their bags) from Tampa, Florida all the way to DC and back without so much as a gripe about the lack of confront or headroom... Ok, my friends and I are all on the shorter side so a several thousand mile road trip may not bode well for your passengers if they are tall and in the back seats.

Just last spring break, I had 9 people riding in my car in St. Augustine because my room mate's SAAB broke down. When I bought the car I didn't have any of this in mind, but that only makes me appreciate my car even more

TL;DR: Get the hatchback because it invites more opportunities, and thus, more good memories. And also get it in stick ;)

Im similar to you, I want to enjoy my ride. I do care about reliability ofcourse as everyone does. I checked out consumer reports for 2016 and Toyota is ranked #2 and mazda is #6 (http://www.consumerreports.org/car-reliability/car-brands-reliability-how-they-stack-up/)

So that's not too bad of a difference.

Millions of cars were affected by the Takata airbag recall. I helped with inventory at a Honda dealer last December, the parts warehouse was crammed to the brim with replacement airbags. There had to be at least 1000 of them.

Posters report success buying an FOB on Amazon and having a licensed locksmith program it.

I would call around to local locksmiths first. They will know the drill. They can come to your home and program the FOB and cut a key from a van. If you negotiate a bit and offer to go to them, you might get the FOB and programming for under a $100.

Let us know how it goes.

I used a some 3M vinyl faux carbon fiber wrap I bought off amazon. Here's the link to what I used -

3M 1080 CF12 BLACK CARBON FIBER 60"x12" Vinyl Flex Wrap https://www.amazon.com/dp/B0058DIDTY/ref=cm_sw_r_cp_api_HX3WybXGBKWFA

Like when people put the edge guard in chrome on every edge on their car like this https://www.amazon.com/dp/B071D8R7MH/ref=cm_sw_r_cp_apa_i_7xmfFbRNF02BB

That's fancy right?! Lol

Trim the gas tank door, trunk, doors, hood, rain guards, interior... Lol

http://www.consumerreports.org/car-reliability/car-brands-reliability-how-they-stack-up/

Even within your link, the Fiat Chrysler brands take up the 4 lowest spots, and Jeep is only slightly above a few others.

Mazda still looks to be on a very short list of manufacturers not offering Android auto and from what I can tell they only one in the market they have the most competition (ie hyundai, kia, Toyata, Honda, etc). You can see the whole list here: https://www.android.com/intl/en_ca/auto/

It's unfortunate because my Wife's car has it and it's honestly the best feature in modern headunits that I have seen ever. The fact that I can use waze and get on demand traffic and searching right from the car's large screen without paying an extra fee for a manufacturers service is the best part.

Fwiw : https://www.android.com/intl/en_us/auto/ - Mazda listed. Additionally, read here for more info on everything having to do with the infotainment system : http://mazda3revolution.com/forums/2014-mazda-3-skyactiv-audio-electronics/57714-infotainment-project.html#/forumsite/20910/topics/57714

This will be easiest to do if you pull the whole seat out.

There should be 4 bolts holding the slider rails to the floor. They may be inverted torx but those sockets are cheap enough. You may have to slide the seat all the way back to get to the front bolts and all the way forward to get to the rear bolts.

You'll have to disconnect some electronics (airbag, seat occupancy sensor, seatbelt sensor, seat heaters, etc) so DISCONNECT THE BATTERY FIRST. It's incredibly unlikely that leaving the battery connected while disconnecting will trigger the airbag but if it happens in your face, you're going to have a bad time.

Once you get the seat out, you should be able to figure how the plastic trim comes off. Odds are, it's a couple of screws and/or plastic pins and then it will either just fall off or slide forward and/or backward. Once the plastic trim is off, you should be able to re-attach the cover hooks.

Reassembly is the opposite of disassembly.

Source: I've replaced the seats in a 2005 RX-8, 2017 Miata RF, and 2009 Infiniti G37.

I'm in love with silicone LED strip sheath... or whatever you want to call it. I went a kind of hacky route, I bought this stuff along with some addressable RGB led strip. Cut the boring white stuff out, stuck the addressable stuff in. You can get it premade but it's spendy.

Technically those are projector headlights. All bulbs lose their effectiveness over time. I bet a combination of the plastic degrading and the bulbs not shining as bright contribute to what you're seeing. Have you tried using a product like 3m or Sylvania headlight restore? I've found the 3M is the easiest to work with and for ~$10 it's hard to beat.

I'll have to keep looking to see what I can find. I think I found some potential HID replacements off Amazon. Those are just one set I am looking at for comparison.

I've also read that HIDs can be used as high beams as well, but then I've read contradictory info that says they can't. I have other bulbs that need replacing other than my low beams, plus I need new hydraulics for my hatchback. It's just a lot of stuff at once.

I appreciate all your feedback! It's been very helpful.

Unless they drastically changed the design I'd say this is total bullshit. I have a 2013 cx5, purchased a ~$120.00 hitch from Amazon and installed it with my wife helping supporting it in like 45 mins.

Edit: https://www.amazon.com/dp/B007Y593B6/ref=cm_sw_r_other_awd_LiBjwbB5QZT1H

That's the hitch Mount I got. If I recall correctly it's just like 2 rubber Supports on each side that you need to slide out and bolt the hitch Mount on (super easy and I'm not very mechanically savy) videos are on YouTube I think.

As for the actual bike Mount I got super lucky and bought one of these locally for cheap https://www.1upusa.com/product-quikracksilver.html solid and easily expandable for more bikes.

Edit 2: let me know if you want pics of it installed to see how it looks.

1) Replace front brake rotors. If the pads are worn significantly or in bad condition, also replace those. Get some Centric Rotors off of Rock Auto, Amazon, or Tirerack. Best price seems to be Amazon at $32/rotor with prime shipping. Centric Parts 120.45068

2) Could be the motor mounts. Not too familiar with the regular Mazda3, but you might be able to get some cheap stock ones from Mazdaspeed3 guys who replace them with upgraded aftermarket units.

3) Most likely wheels need to be balanced.

4) Wiper blades need to be replaced much more often than most people think. I'd get some

Here's the Amazon link. It works alright, seems to charge fast enough to use navigation with and maybe gain a few % along the way.

At work now but this is the instructions that I will be going by.. http://sidesonic.blogspot.com/2015/05/mazda-3-bl-hvac-air-actuator-replacement.html

and here is the part on Amazon..

https://www.amazon.com/gp/product/B01D8VOG8E/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Just bought my Mazda 3 Hatchback on Sunday. I searched for cases for my key fobs as well and took a shot at these off amazon!

This is how they look on my key fob. Notice the ones I purchased do not have the trunk button but the link you posted did. My key fobs do not have the trunk button because I have the Hatchback so you might want to stick with the link you posted since you have the Mazda 6 with a trunk. Hope this helps!

I just got my touch-up at the Mazda dealer. Sure you pay a little more, but you're guaranteed to get the right color.

Amazon claims to have "Genuine Mazda" touch up paint: https://www.amazon.com/Genuine-Mazda-0000-91-42S-Touch-Up-Paint/dp/B00K8XDHWW

we used something similar when I used to work in a warehouse to keep merchandise separated on a truck. This may work for you.

http://www.amazon.com/Keeper-05059-Ratcheting-Cargo-Bar/dp/B0000AZ9KS/ref=sr_1_2?s=automotive&ie=UTF8&qid=1434880090&sr=1-2

Two months is a decent stretch. Either uncouple the lines or use a tender. Battery Tender, listed by Celestial, is a good brand but you should do OK with a more basic version. http://www.amazon.com/Battery-Tender-021-0123-Junior-Charger/dp/B000CITK8S/

Huh, this also popped up on my Facebook feed earlier. I wasn't sure where I was for a moment.

Those 3M kits work really well, but they tend to go hazy again pretty quickly afterwards. I'm trying this Meguiars protectent, but haven't had it on long enough to really tell if it helps.

Car batteries don't like to be discharged. I use a float charger whenever I leave my car for a few weeks. This will charge your battery to full capacity then maintain it without overcharging. If you don't have time to get one of these definitely disconnect the battery.

This velcro tape with the cobb mount works great. I've had this on my original V3 mount for a year and a half without failure.

here you go, I mean it looks like crap but works great. https://www.amazon.com/Carlinkit-Achieve-Wireless-CarPlay-Android/dp/B0B1TZZ9K3/ref=sr\_1\_4?crid=GNQ0UVSRDXXE&keywords=car2play&qid=1671259056&sprefix=car2play%2Caps%2C129&sr=8-4&ufe=app\_do%3Aamzn1.fos.f5122f16-c3e8-4386-bf32...

Hi! I have a 2016 Mazda6 grand touring with wheels that look "graphite" or "gunmetal" to my eyes. They're darker than the more silver-ish looking ones on the touring trim. Does anyone know if there is either a factory or aftermarket paint that matches well for fixing curb scuff? My searches have led me to a few older posts and inconclusive information, ranging from:

• Custom color that has to be mixed. Dealerships don't carry it and will sub out refinishing to a service that specializes in this.

• Duplicolor "graphite" paint, which looks pretty close is somehow unreasonably hard to find for purchase!

• Rustoleum silver touch up paint, which looks a little light to me and I'd also prefer a spray can.

Also found this Rustoleum graphite but it's hard to tell from the picture if it would be a good match. Any suggestions from pros and DIYers alike welcome! I thought this would be a fun little winter project when the snows are swapped on.

https://www.amazon.com/JF-EGWO-2000Amp-Portable-Compressor-Inflator/dp/B08T6N7X51/?_encoding=UTF8&pd_rd_w=YwYF7&content-id=amzn1.sym.e4bd6ac6-9035-4a04-92a6-fc4ad60e09ad&pf_rd_p=e4bd6ac6-9035-4a04-92a6-fc4ad60e09ad&pf_rd_r=E8B4CE9J...

this is the unit i have for portable air, more of a jump starter

Google the size bulb you need for your license plate lights. When you go to search for the bulbs themselves you’re going to be looking for cool white or bright white LEDs. You should be able to just search YouTube how to replace the bulbs yourself. Here’s an example of some bulbs on Amazon. Amazon bright white led

Hello all. I saw a similar video showing the start-up speed/functionality of wireless Carplay on this subreddit a while back, and wanted to add my experience as another generally positive review of the process. I have a 2022 Mazda 3 Select.

After some light research, I bought this CarLink adapter on Amazon

I followed the instructions outlined in the top review of this item, which required some additional steps (primarily updating firmware multiple times before setting up the Bluetooth connection and tweaking a couple of settings). As you can see in the video, the wireless Carplay starts automatically in about 15-20 seconds. There is a small input delay between when you select a song, for example, and when it actually plays. I’d estimate that delay to be about 1 full second. Not ideal, but not a deal breaker for me at all. Other than that delay, I have not had a single other issue with this setup after about 2 weeks of daily use. If that changes, I will come back and edit this post. Feel free to shoot any questions my way.

You can replace it with a Switchback LED bulb like this one:

https://www.amazon.com/LASFIT-CANBUS-7444NA-Switchback-Standard/dp/B08294XHC7/ref=sr\_1\_3\_sspa?crid=31UU8TZ36T9CS&keywords=7443+led+lasfit&qid=1664911659&qu=eyJxc2MiOiIyLjcyIiwicXNhIjoiMi40MiIsInFzcCI6IjAuMDAifQ%3D%3D&sprefix=744...

​

That will give you amber for your turn signal but white when your headlights are on

https://www.amazon.com/AmeriLite-Crystal-Headlights-Black-Protege/dp/B07TP5FRYQ/ref=mp_s_a_1_3?crid=WEKLK3M8ZDIM&keywords=mazda+protege5+euro+headlights&qid=1664036212&sprefix=mazda+protege+5+euro+headligh%2Caps%2C203&sr=8-3

Here is what I used. They have a few color options. shunyang Car Neon Light El Wire

https://www.amazon.com/dp/B094QK16JJ?ref=ppx_pop_mob_ap_share

Since it is EL it will not be a transparent wire. They do sell a type of wire that are transparent but they rely on light emitters. These can get hot during operation and if you curve the wire in any way you can block the light from the emitter.

The very top Layer has been coming away in tiny black flakes, another forum post suggested this is not the leather itself but the coating that Mazda applies? Just wondering if anyone has tried this type of product:

https://www.amazon.co.uk/Furniture-Clinic-Leather-Steering-Restore/dp/B07H95DMJJ

Friend, please, get these. These will fit and aren't stupid expensive like the OEM parts.

Literally the same plastic OEM or not.

Wheel Caps

This is a Fakespot Reviews Analysis bot. Fakespot detects fake reviews, fake products and unreliable sellers using AI.

Here is the analysis for the Amazon product reviews:

>Name: Vantrue E1 2.5K WiFi Mini Dash Cam with GPS and Speed, Voice Control Front Car Dash Camera, 24 Hours Parking Mode, Night Vision, Buffered Motion Detection, APP, Wireless Controller, Support 512GB Max

>Company: Visit the VANTRUE Store

>Amazon Product Rating: 4.1

>Fakespot Reviews Grade: D

>Adjusted Fakespot Rating: 1.1

>Analysis Performed at: 08-11-2022

Link to Fakespot Analysis | Check out the Fakespot Chrome Extension!

Fakespot analyzes the reviews authenticity and not the product quality using AI. We look for real reviews that mention product issues such as counterfeits, defects, and bad return policies that fake reviews try to hide from consumers.

We give an A-F letter for trustworthiness of reviews. A = very trustworthy reviews, F = highly untrustworthy reviews. We also provide seller ratings to warn you if the seller can be trusted or not.

After you get it cleaned and sprayed, get some Mazda sill protectors to cover it all up. Something like these, Sill protectors

I'm doing the same thing but 2016 mazda 6, buy this if it's applicable which i believe your car would be but it's your car so i'll let you do the research :) https://www.amazon.com/gp/product/B001715RQS?ref=ppx\_pt2\_dt\_b\_prod\_image&th=1

Congrats man. Love that. Can't help but notice yours has the silver line running along the fog lights. That's a nice touch, I don't know why mine doesn't have that :(

These are the lights I have added. They do the job nicely & sync to music, but need a remote control. There's other lights you can control/sync with an app, that'd probably be better.

Drive Auto Car Trunk Organizer -... https://www.amazon.com/dp/B071F82CYJ?ref=ppx_pop_mob_ap_share

Just got that today for the cx5. It's 40% off right now but been cheaper in the past.

I also have some of those cistco installed crates. And then some insulated fold out things to go inside them. Hope that helps

I use Mazda Moly 0w-20 in our 2014 Skyactiv CX-5. Supposedly this oil from Idemitsu is the same stuff. https://www.amazon.com/Idemitsu-Synthetic-Engine-GF-6-5-30013012-95300C020/dp/B08CS113XC/ref=sr\_1\_9?crid=16XJN1YRWNGJI&keywords=mazda+moly+oil&qid=1654800854&sprefix=mazda+moly+oil%2Caps%2C82&sr=8-9

Amazon link, but less at REI, where I grabbed mine. I got 28s, but could probably fit 32.

I want to patch/repaid those two bottom panels which sit on my lower back. I’m trying to avoid a seat cover if possible. I found this link for a kit

ILOFRI Leather and Vinyl Repair Tape 3x60 inch, Strong Adhesion Backing Self Adhesive Vinyl and Leather Repair Kit for Car Seat, Couch, Furniture, Jacket. Bonded Leather Repair Roll - Navy Blue https://www.amazon.com/dp/B092MLJKK5/ref=cm_sw_r_cp_api_i_DT9MSSCMHJBCRQ8K6A5M?_encoding=UTF8&psc=1

They have beige, ivory, and khaki. Mazda’s official name is Sand for the interior but I’m not sure which one to pull the trigger on. Anyone have experience or better suggestions? Thanks in advance!

USB USB 12V adapter

USB for 12V change out

Exact parts that I got from crutchfield

this is what im refering too

https://www.amazon.com/Gold-Label-Detailing-Applicator-Construction/dp/B07N95TXM8/ref=sr_1_1_sspa?keywords=well+pen+touch+up&qid=1653340563&sprefix=well+pen%2Caps%2C320&sr=8-1-spons&psc=1&smid=ALRPFGEN62HZC&spLa=ZW5jcnlwdGV...

Amazon link for clips

Try 303 Protectant— it’s similar to sprays like armor all, but with an almost matte finish.

https://www.amazon.com/dp/B0185PU38A/ref=cm_sw_r_cp_api_i_3464JBF63KKTYFJE2FZB?psc=1

Also, if it’s not already installed, the Airplay/CarPlay kit is a must-have.

yeah quad lock is the brand, he probably meant something like this (sorry for my german amazon) https://www.amazon.de/QUAD-LOCK-QLM-CAR-4-Quad-Autohalterung/dp/B089LQ78BL/ref=mp_s_a_1_3?crid=31KFWYC7B5E80&keywords=quad+lock+mount+car&qid=1652253647&sprefix=quad+lock+mount+car%2Caps%2C59&sr=8-3

I figured that would be the case. Thanks for confirming. Do you remember where you bought it from? I was searching on Amazon and I found this remote start for less than what you paid. I'm wondering if the price for what you bought is less now than it was back then.

I wonder if something like this would be similar? https://www.amazon.com/Conditioner-Decoration-Universal-Waterproof-Accessories/dp/B09DYKXQNJ/ref=sr\_1\_5?crid=25LZJDLTZ3WSA&keywords=mazda%2Bcx-5%2Bgrill%2Bdecor&qid=1651870696&sprefix=mazda%2Bcx-5%2Bgrill%2Bdecor%2Caps%2C165&sr=8...

It’s Mothers California gold wax. It’s takes a lot of work to put it on but it lasts 8 weeks. Been using it for 20+ years. I used to help my Dad wax his Trans-Am and that’s what he used.

https://www.amazon.com/Mothers-California-Brazilian-Carnauba-Cleaner/dp/B0002U1TVW/ref=asc_df_B0002U1TVW/?

But if the dealer offers the Ceramic coating I think it’s worth it. The MX-30 Came with it from the dealer and it’s definitely easier to keep looking clean.

So the floor is 6mm or 1/4” Rubber king solid mats.

https://www.amazon.com/Dinoflex-Rubber-King-Performance-Flooring/dp/B08178J99T?

It took 18 boxes to do the floor, they were easy to work with and lock together tight. They reduce the echo in the garage and insulate the floor from being cold in the winter.

They are waterproof and you can pull individual tiles if they get dirty or need to be replaced. I found black magic tire shine gel works great on them since they are solid rubber.

More expensive than epoxy with flakes but they are a way better product IMO.

I also insulated the Garage door and put a mini split heat/Air Con system in. I haven’t been running the Heat/AC system it’s mainly for super hot days and super cold days. Basically to keep the Garage under 90F and above 50F

Short of painting it yourself with a fine brush or master taping skills to spray it not really.

I just buy these silicone covers for my key fobs they fit perfect and protect the key Alegender 2Pcs Silicone Smart Key Fob Cover Case Protector Holder for 2017 2018 2019 2020 2021 Mazda CX-5 CX-7 CX-9 MX-5 Miata Mazda 3 6 Key Remote 4 Buttons https://www.amazon.com/dp/B07B4Z7FV3/ref=cm_sw_r_cp_api_i_YZ5FNVS5SG3NQNWJKZJ5

I’m new to Mazda so I don’t know how the back of your head unit is.

but I did this for my old Acura TL that had a headunit only with cd and cassette.

They have on Amazon eBay etc an adapter that plug into the back of your cars head unit (as long as their is a port for a multiple disc changer)

Here is an example: Auxillary adapter,Moonet USB AUX in Car Digital Cd Changer for Honda Accord Civic Odyssey S2000 City Ridgeline CRV Element Pilot Fit Connect Old Connector https://www.amazon.com/dp/B00ISQX1J0/ref=cm_sw_r_cp_api_i_A1M17H82WS0AAYQHF0G6?_encoding=UTF8&psc=1

And you’ll see on the user end there is a 3.5 mm Jack and there is also an iPod plug (30 pin plug). Since the 30 pin brings power, I found a Bluetooth 30 pin adapter that would fit and plugged it in. It was powered by the car and I was able to stream music from my phone through the head unit using Bluetooth.

I will suggest using an OBD hardwire cable. I use for my Thinkware and parking mode works perfectly. I did try fiddling with fuses and wasted money on a hardwire kit. Realized that 2021 CX 30 didn’t have any fuse that turned off with ignition after much effort. Check if your dashcam supports a similar one THINKWARE OBD-2 Hardwiring Cable I OBD-II Cable Enables Parking Mode I Plug & Play https://www.amazon.ca/dp/B08KTTCKJ8/ref=cm_sw_r_cp_api_i_CFVQMJQZ3YHTBP8SGE3X?_encoding=UTF8&psc=1

HIBEYO Key Fob Cover for Mazda 3 Alexa CX4 CX5 CX8 2019 2020 Smart Key Case Side 3 Button with Keychains for Key Accessories https://www.amazon.ca/dp/B09PHBQC5V/ref=cm_sw_r_apan_i_JE3WKZ24BF6PHYCRVH86?_encoding=UTF8&psc=1

I got this, I personally didn't find it too thick. I would suggest not getting white like I did because it has some kind of skidd mark on it already lol

Thanks!! Here is the link for the store on Amazon and the link for the mats

https://www.amazon.com/stores/page/5AFA8707-DCC6-49ED-B4DB-A003019A84B5

https://www.amazon.com/Dinoflex-Rubber-King-Performance-Flooring/dp/B08178J99T?ref_=ast_sto_dp&th=1&psc=1

It’s kinda pricey for that 20x20 garage I had to buy 20 boxes. They don’t sell edge pieces so some pieces had to be custom cut with a metal ruler and a razor blade.

I was going to do epoxy and flakes but this is way nicer and I heard the horror stories about it needing multiple coats to get it to look good.

I hate painting anyways it’s always a mess and cleanup is a pain. So I went with this, yeah it’s 4x more money but it’s nice on the feet and keeps the garage warm in the winter.

It’s the one linked below. Took about 45 min to install and delivered in two days. Thank you!!

Mophorn Roof Rack Compatible with Mazda CX-5 CX5 2017 2018 2019 2021 4PCS Roof Rack Rail Cross Bar Crossbar https://www.amazon.com/dp/B07PM3QZXZ/ref=cm_sw_r_cp_api_i_GK76MX96FQSP3K1B9KSR?_encoding=UTF8&psc=1

I use these $13 Bosch ones: Bosch Automotive 6080C HEPA Cabin Air Filter for 2013-2019 Mazda CX-5, 2016-2019 Mazda CX-9, 2014-2018 Mazda 3, 2014-2018 Mazda 3 Sport, 2014-2019 Mazda 6 https://www.amazon.com/dp/B07M8J9LNC

They last a long time. There are some cheaper off brand ones on Amazon too.

I have this one that plugs directly into the car and this Bluetooth one that only works on Android phones. Both have been working great for me for years.

I picked up a set of SmartLiner on amazon. I have a 2022 Touring Plus, captains chairs w/o the center console. These were one of the only ones that fit that setup, everything is for the bench seat configuration. The first and second rows fit excellent, the third row is a little off but I think with some persuading it will fit great.

These brushes from the Detail Factory are amazing. Super soft, similar to makeup brushes Detail Factory Ultra-Soft Detailing Brush Set, Comfortable Grip and Scratch-Free Cleaning for Exterior, Interior Panels, Emblems, Badges, Gauge Cluster, Infotainment Screen https://smile.amazon.com/dp/B0743M4VZH/ref=cm_sw_r_cp_api_glt_i_NKAREGQ5EC5THA097Q1N

For backup camera, I have a cheap eBay one on my 5 that clips onto the license plate light. I believe its compatible with other Mazdas as well.

https://www.flickr.com/photos/tuanies/13251794855/in/set-72157641783897914

Wholesale, or auction, prices are what you'd be looking for. Since there's no way for you to really know that, you can come in the ball park with the trade-in value. This represents what the dealer paid, or at least gives you an idea of where their cost generally is. Then there's the markup, delivery cost for the dealership, advertising, etc etc. There are dealer fees that you'll notice cover all of this stuff, yet the price is way higher than the trade in value. It's your negotiating ability that will determine the price of the car at this point. You can look up the KBB and TrueCar fair market value for retail and this car may be on the low end of that curve already, but that doesn't mean you can't drive a bargain out of them still, especially if this car has been in accidents before. This would mean the dealer presumably paid even less than trade in value for it. This was one of the articles I read that I kept revisiting when I bought mine.

http://www.consumerreports.org/cro/cars/used-cars/buying-advice/index.htm

I have MAXspider. Love them and their premium look. I had weathertech in my previous vehicle and didn't think the look went with my Signature.

The only thing I'd advise against it is if you live in a snowy climate. Not sure they'll divert snow and slush well enough.

I bought the lights from Amazon (EL Wire Interior Car LED Strip... https://www.amazon.com/dp/B096RGGGT2?ref=ppx_pop_mob_ap_share) and installed it myself. Took roughly 20-25 minutes to get it all done!

I got a retrofit USB 3.0 Hub for $150 from a local seller.

Amazon sells them for around the same price.

Just make sure you update to the newer firmware with a USB 2.0 flash drive before putting the new Hub in.

Took me about 4 hours to figure out how to take the dash apart, swap the part and put everything back together.

Bought these leather fob covers for my 2021 CX-5.

https://www.amazon.com/gp/product/B087MYCNZ7/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&th=1

They list the dimensions as ‎3 x 0.5 x 3 inches.

Your headlight is already a projector so putting in an HID or LED bulb setup is not hard. The "blue lights" you describe are probably people adding HID/LED to a normal halogen non-projector headlight. I believe you have an H11 style bulb so this may work for you:
https://www.amazon.com/Fahren-Headlight-Headlights-Conversion-Waterproof/dp/B07NPMV1H5/

There are some aftermarket companies that make vehicle-specific wireless chargers and there are options available for the 2020 CX-5 which is essentially a 2-row version of the CX-8.

Here’s an option on Amazon.

I think these are the same ones shipped from crutchfield. Be sure to snap off the interior tabs (both the single and double holed tabs) to accommodate the 6.75 inch speakers. Good luck mate

Metra 82-7400 Speaker Adapter for Nissan/Infiniti Vehicles https://www.amazon.com/dp/B0194MS420/ref=cm_sw_r_apan_glt_i_VDVVAXH2SH901SEN7GJN

Amazon has a nice one I bought a few years back. Its kinda a bitch to sew on yourself but looks really nice!

Loncky Black Leather Suede Auto Custom Steering Wheel Covers for 2013 2014 2015 2016 Mazda CX-5 / 2014-2016 Mazda 6 / 2014-2016 Mazda 3 / 2016 Mazda CX-3 / 2016 Scion iA Accessories https://www.amazon.com/dp/B00QKHWSF2/ref=cm_sw_r_cp_api_glt_fabc_BNQBQJ63MFTVN5C1T1J7?_encoding=UTF8&psc=1

Some cars are manufactured with fish eye (I think this is what the OP maybe referring to) which is good. On some of the newer cars with side car detection the light on the mirror makes the placement of the fish eye a bit challenging. I like the fish eye in the upper most outside of the mirror but that's where my side car detection light is.

These are what I use. They have no ugly ring and sit as flush on the mirror as possible.

https://www.amazon.com/dp/B00VCPEEX6/ref=cm_sw_r_apan_glt_fabc_4VAY0ZB9NG54GV848TB4?_encoding=UTF8&psc=1

There's a specific LOC for the 3rd gen on Amazon I think it was. It connects behind the passenger kick panel/below the glove box. It works. Did it in my '15. Direct plug and play. PAC AOEM-MAZ2 Interface That Allows Replacement or Addition of an Amplifier in Select Mazda Vehicles https://www.amazon.ca/dp/B001715RQS/ref=cm_sw_r_apan_glt_i_BHS1ZC5J70Y49YRE8HGV

I never exit CarPlay so I don’t know if it works in the built in media interface. Essentially all wireless CarPlay adaptors are the same, using the exact same chips and software. But i bought this one: OTTOCAST Wireless Carplay Adapter【Official Genuine Latest】Fastest Speed for Cars with Factory Wired CarPlay (Model Year: After 2016), Wired to Wireless CarPlay, Carplay Wireless Adapter Compitable for Mercedes Jeep Toyota Nissan Hyundai etc U2-NOW https://www.amazon.ca/dp/B09BJDBZPX/

That was the first thing I did with my 2016. There's a special place in hell for whoever made the decision to use those allen key plugs. I 100% recommend the swap. I sourced mine from Amazon, but it's the same thing your parts guy is referring - same thread pitch, so no worries about fit. It should also come with a new crush washer as well.

If you have a 2021, you're in luck

otherwise, try searching eBay for part no. BHP166EZ1N (or BHP166EZ1M). that's what I ended up having to do.

I'm in Canada so I think it's available. Is it this one? AmazonBasics Double Braided Nylon USB Type-C to Type-A 3.1 Gen 2 Charger Cable | 1 foot, Dark Grey https://www.amazon.ca/dp/B07D7PM3S4/ref=cm_sw_r_apan_glt_i_3YRX9CD4AV9JHKY2DESQ?psc=1

For those who happen across this post, this is what I got that kept disconnecting. Although I'll have to actually test a new one to confirm that was the issue.

USB C Cable, INIU [5 Pack] 3.1A... https://www.amazon.ca/dp/B08JPJD5Y4?ref=ppx_pop_mob_ap_share

Yea it was the trails.

Confused them with the 16" I was going to get but my rims for the '17 non turbo do not clear the brakes.

I would recommend using some upholstery cleaner on both the cloth seats and the carpet.

I use Folex and any upholstery brush should do the trick.

Just spray the area with the cleaner and then scrub with the brush. Afterwards, vacuum the area and go about your day. It's pretty simple and you should do it regularly to keep it clean.

Flac is easily converted to mp3 via simple scripts, or free programs like Foobar 2000, and all of the tags should carry over. Now, the system is Linux with GStreamer, and flac has no licensing issues, so there's really no reason the system shouldn't support it (unless they were trying to save space by not including a library), but I think it's a limitation that's easily worked around.

Please consider mileage if you decide installing a roof rack.

http://www.consumerreports.org/cro/news/2013/07/tests-show-bike-racks-can-ruin-your-mileage/index.htm

This alone makes me want to stay away from it.

It took me 5s on Google to find this... Similar enough? Not sure.

McGard 24157 Chrome Cone Seat Wheel Locks (M12 x 1.5 Thread Size) - Set of 4 https://www.amazon.com/dp/B000CONU1K/ref=cm_sw_r_apan_glt_fabc_HF78Q2K279DQNTRDMVSB?_encoding=UTF8&psc=1

A buddy of mine used something like this https://www.amazon.ca/dp/B07XQHH993/ref=cm_sw_r_apan_glt_i_YZVFGKYT5S1TX3NN6MSY in his old Subaru Forester. Had a tape deck, but no aux or media button like your car. Worked like a charm for him

You can buy felt tape and put a small piece on the arm rest, the squeak drove crazy and that solved it. Here’s the link Keenso Felt Tape Automotive, MultiPurpose Car Wiring Harness Tape Self Adhesive Anti Squeak Rattle Tape Dash, Black (9mm × 25m) https://www.amazon.com/dp/B07DW6FJCS/ref=cm_sw_r_cp_apip_D5JZ6WaWGTUVO

good eye, and /u/BillWordsmith actually got it!

https://www.amazon.com/dp/B06ZXRSHH2/ref=cm_sw_r_cp_api_glt_fabc_R21PDS5HBDSM5A2XVWCD?psc=1

it fits REALLY snug, and is a soft touch feaux leather marerial

just an FYI that it does make the steering wheel noticeably thicker. only downside!

That appears to be the face lift model from 2010, it got some minor changes to the styling that hardly notice like the front lights in the bumper have been moved a little and some chrome trim added. They also dropped the twin exhaust on the 2.2 for the single (pre facelift had the twin pipes) found a similar model European spec listed as a sport for comparison https://www.gumtree.com/p/mazda/bad-credit-car-finance-available-2011-11-mazda6-2.2d-180ps-sport/1245196115 (link for images only, i have no conection to the site)

My alarm bell went off when i looked at the images you posted because of the location the seller chose to take the pics? most people take the pics outside their homes and not on a deserted industrial complex plus it's still wet from being washed. It might mean nothing but if the price is to good to be true it might be better to walk away.

If you do decide to buy it then do a full history check on it and physically check the VIN that's stamped into the bulkhead matches the little plate in the corner of the windshield to make sure they have not been tampered with. (any signs of tampering means it's a stolen car)

I have bought a lot of vehicles over the years and know what to look for and i have been caught out myself. Best of luck.

On the Android auto site it still says coming soon. https://www.android.com/auto/mazda/ Although I have heard that July is the month that updates will start going out. I just bought my CX-3 yesterday but was a little bummed that I couldn't do it myself due to the USB block that was pu into effect with .502. Oh well, I can wait. I love the car, I had a 2004 Honda Civic before. I feel like I'm driving a spaceship.

Where?!?!? Where does one acquire such a gift? I've only seen one so far since I've made this post, and it supposedly has a "corvette engine" in it, and he's selling it for $22,000 dollars. https://www.facebook.com/marketplace/item/158342988162781

Thanks for your reply.

I'm in Canada, so I'm going to have to go with an alternative, as I didn't want to pay $15 shipping fee from Invisicord: https://www.amazon.ca/gp/product/B00U2DGJOQ/ref=ox_sc_act_title_1?smid=A3CA5H83RV6W5M&th=1

The A119 v3 dashcam has miniUSB.

Can I interest you in a FOB Cover. I know it's a bandaid, but it fits so snuggly your FOB will stay in one piece.